S-812C Seiko Instruments Inc, S-812C Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
S-812C
Manufacturer Part Number
S-812C
Description
HIGH OPERATING VOLTAGE CMOS VOLTAGE REGULATOR
Manufacturer
Seiko Instruments Inc
Datasheet
1.S-812C.pdf
(26 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
S-812C20AMC-C2AT2G
Manufacturer:
PANASONIC
Quantity:
2 164
Part Number:
S-812C20AMC-C2AT2G
Manufacturer:
SEIKO
Quantity:
20 000
Company:
Part Number:
S-812C23AUA-C2D-T2
Manufacturer:
SIEKO
Quantity:
47 000
Company:
Part Number:
S-812C25AMC-C2F-T2
Manufacturer:
HOLT
Quantity:
101
Part Number:
S-812C25AMC-C2FT2G
Manufacturer:
SII/精工
Quantity:
20 000
Company:
Part Number:
S-812C28AMC-C2IT2G
Manufacturer:
SEIKO
Quantity:
9 000
Part Number:
S-812C28AMC-C2IT2G
Manufacturer:
SEK
Quantity:
20 000
Part Number:
S-812C30AMC-C2K-T1
Manufacturer:
SII/精工
Quantity:
20 000
Company:
Part Number:
S-812C30AMC-C2K-T2
Manufacturer:
SEK
Quantity:
3 000
Part Number:
S-812C30AMC-C2K-T2
Manufacturer:
精工/SII
Quantity:
20 000
HIGH OPERATING VOLTAGE CMOS VOLTAGE REGULATOR
S-812C Series
Selection of External Components
8
3. Power-off function (ON/OFF pin)
4. Short-circuit protection
The ON/OFF pin controls the start and stop of the regulation operation.
When the ON/OFF pin is set to power-off level, halting whole internal circuit and turning off the Pch MOSFET
between VIN and VOUT, current consumption is drastically reduced. The voltage of the VOUT pin becomes
VSS level due to the internal resistance divider of several M between VOUT and VSS.
The ON/OFF pin should not be left afloat since no pull-up nor pull-down is made internally as shown in figure
10. Note that the current consumption increases if a voltage between 0.3V and VIN-0.3V is applied to the
ON/OFF pin. When the power-off function is not used, connect the pin to the VIN pin in case of positive logic
and to the VSS pin in case of negative logic.
When a regulation operation at light load less than 100uA is halted, output voltage
may increase. If the increase of the output voltage should be avoided, pull down the VOUT pin to the V
as soon as ON/OFF pin goes to the power-down level.
Installation of the short-circuit protection which protects the output transistor against short-circuit between
VOUT and VSS can be selected in the S-812C series. The short-circuit protection controls output current as
shown in the typical characteristics, (1) OUTPUT VOLTAGE versus OUTPUT CURRENT, and suppresses
output current at about 40 mA even if VOUT and VSS pins are short-circuited.
The short-circuit protection can not at the same time be a thermal protection. Attention should be paid to the
Input voltage and the load current under the actual condition so as not to exceed the power dissipation of the
package including the case for short-circuit.
When the output current is large and the difference between input and output voltage is large even if not
shorted, the short-circuit protection may work and the output current is suppressed to the specified value.
Products without short-circuit protection can provide comparatively large current by removing a short-circuit
protection.
Output Capacitor (C
The S-812C series can provide stable operation without output capacitor (C
internal phase compensation circuit to stabilize operation when the load changes. The transient response of
the regulator, however, changes with the output capacitor and the magnitude of overshoot and undershoot on
output voltage accordingly changes. Please refer to C
Characteristics” to select suitable value for the capacitor. .
When a tantalum or an aluminum electrolytic capacitor is used, the ESR of the capacitor shall be 10
When an aluminum electrolytic capacitor is used attention should be especially paid to since the ESR of the
aluminum electrolytic capacitor increases at low temperature and possibility of oscillation becomes large.
Sufficient evaluation including temperature characteristics is indispensable.
Product
type
B
B
“H” : Power on
“L” : Power off
ON/OFF pin
L
Table 8 Power-off function
)
Operate
Internal
circuit
Halt
Seiko Instruments Inc.
VOUT pin
Set value
V
voltage
SS
level
L
dependence data in “Transient Response
consumption
Current
I
I
ss
ss
2
L
) since the regulator has an
ON/OFF
Figure 10
VSS
VIN
Rev.1.0
or less.
SS
level