D2S-5LD Omron Corporation, D2S-5LD Datasheet
D2S-5LD
Related parts for D2S-5LD
D2S-5LD Summary of contents
Page 1
... D2S-10L2 0.18 N {18 gf} --- 0.49 N {50 gf} D2S-10L2D 0.18 N {18 gf} --- D2S RC Model 5 A 0.1 A D2S-5 D2S-01 D2S-5-F D2S-01-F D2S-5D D2S-01D D2S-5-FD D2S-01-FD D2S-5L D2S-01L D2S-5L-F D2S-01L-F D2S-5LD D2S-01LD D2S-5L-FD D2S-01L-FD D2S-5L13 D2S-01L13 D2S-5L13-F D2S-01L13-F D2S-5L13D D2S-01L13D D2S-5L13-FD D2S-01L13-FD D2S-5L2 D2S-01L2 D2S-5L2-F D2S-01L2-F D2S-5L2D D2S-01L2D D2S-5L2-FD D2S-01L2-FD ...
Page 2
... VDC 0.2 A 0.03 A Note: 1. Data in parentheses apply to the D2S-10 models only. 2. The above values are for the steady-state current. 3. Inductive loads have a power factor of 0.4 min. (AC) and a time constant max. (DC). 4. Lamp loads have an inrush current of 10 times the steady-state current. ...
Page 3
... Mechanical: 400 operations/min max. Electrical: Insulation resistance 100 MW min. (at 500 VDC) Contact resistance OF 1.47 N {150 gf}: D2S-10, D2S-5 models max. (initial value) (see note 2) OF 0.49 N {50 gf}: D2S-5 models: Dielectric strength (see note 3) 1,000 VAC, 50/60 Hz for 1 min between terminals of same polarity 1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground ...
Page 4
... Note: For more information on the minimum applicable load, refer to Using Micro Loads on page 196. Engineering Data (Reference Values) Mechanical Durability (Pin Plunger Models) Ambient temperature: 20±2°C Ambient humidity: 65±5% Operating frequency: 60 operations/min D2S-01 models D2S-5 models D2S-10 models Overtravel (mm) Contact Form D2S-01 0.1 A --- 0.1 A D2S-5 ...
Page 5
... The following figures show models with self-clinching PCB terminals. For the solder terminals, refer to Terminals. 4. The j in the model number is replaced with “D” for self-clinching PCB terminals or removed for solder terminals. 5. The operating characteristics are for operation in the A direction ( ). Pin Plunger Models D2S-01j, D2S-01-Fj, D2S-5j, D2S-5-Fj, D2S-10j (5.3) 2.35±0.05 2.5± ...
Page 6
... D2S Hinge Lever Models D2S-01Lj, D2S-01L-Fj, D2S-5Lj, D2S-5L-Fj, D2S-10Lj t = 0.3* 2.35±0.05 2.5±0.07 dia. Simulated Roller Lever Models D2S-01L13j, D2S-01L13-Fj 0.3* D2S-5L13j, D2S-5L13-Fj, D2S-10L13j 2.35±0.05 2.5±0.07 dia. Hinge Roller Lever Models D2S-01L2j, D2S-01L2-Fj, D2S-5L2j, D2S-5L2-Fj, D2S-10L2j t = 0.3* 2.35±0.05 2.5±0.07 dia. A 3.6 2.35±0.05 dia. 14 7.7 7 1.8±0.1 2 3.3±0.1 3 ...
Page 7
... The equation, λ 0.5 10 cates that the estimated malfunction rate is less than 1/2,000,000 operations with a reliability level of 60%. Operating range for micro load models D2S-01 Inoperable range D2S –6 /operations indi- ...
Page 8
General Information Correct Use No. Area No. Item 1 Using Switches 2 Selecting Correct Switch 3 Electrical 1 Load C Conditions diti 2 Application of Switch to Electronic Circuits 3 Switches for Micro Loads 4 Contact Protective Circuit 4 Mechanical ...
Page 9
General Information Contact Protective Circuit Apply a contact protective circuit (surge killer) to extend contact du- rability, prevent noise, and suppress the generation of carbide or ni- tric acid due to arc. Be sure to apply the contact protective circuit ...
Page 10
General Information Mechanical Conditions Operating Stroke Setting The setting of stroke is very important for a switch to operate with high reliability. The chart below shows the relationship among operating force, stroke, and contact force. To obtain high reliability from ...
Page 11
General Information Incorrect Snap-back Shock operation Correct • Make sure that no improper force is applied to the actuator, otherwise the actuator may incur local abrasion result, the actuator may become damaged or its durability may be deteriorated. ...
Page 12
General Information terminals, otherwise the terminal may be deformed or the housing may be damaged. Wiring Work When wiring a switch, check the insulation distance between the switch and the mounting plate. If the insulation distance is insuffi- cient, use ...
Page 13
General Information Switch Trouble and Corrective Action Type Location Failure of failure Failures Contact Contact related failure electrical characteristics characteristics Malfunction Contact welding Insulation deg ada o degradation (b (burning Failures ...