T210A103J075PS Kemet Corp., T210A103J075PS Datasheet - Page 18

• Manufacturer Part Number: T210A103J075PS
• Description: GR500 High Reliability Solid Tantalum Capacitors; Capacitance: 0.01uF; Voltage: 75V; Tolerance: ±5%; Body Size: 0.250" x 0.125" Lead Style: Axial; Body Style: Hermetically-Sealed; Features: P Failure Rate
• Manufacturer: Kemet Corp.

16
3.8 Workmanship—Capacitors shall be processed in such a
manner as to be uniform in quality and shall be free from cold
soldering, corrosion, pits, cracks, dents, rough edges, and
other defects that will affect life, serviceability, or appear-
ance. Solder on the surface of the case shall be smooth and
unbroken and shall not have any pin holes or girdle.
3.9 Data submittal—Each shipment shall be accompanied
by the following data for the respective lots (see paragraph
3.5.2 and 4.5.3).
In addition, a statement of compliance to this specification
shall accompany each shipment.
3.10 Deviations—Special or non-standard configurations,
designs, finishes, or test requirements requiring deviation to
this specification or the applicable detail specification shall
be subject to negotiation between the procuring agency and
the manufacturer.
4. QUALITY ASSURANCE PROVISIONS
4.1 Responsibility for inspection—The manufacturer is
responsible for the performance of all inspection require-
ments as specified herein.
4.1.2 Reliability assurance program—The manufacturer
is responsible for establishing a reliability assurance pro-
gram complying with the requirements of MIL-STD-790.
4.1.3 Additional inspection—Nothing specified herein
shall preclude the manufacturer from making additional or
more stringent inspection as he may deem necessary or
desirable to assure conformance with the requirements of
this specification.
4.2 Classification of testing and inspection—The testing
and inspection of capacitors shall be classified as follows:
4.3 General test requirements
4.3.1 Inspection conditions—Unless otherwise specified,
all inspection shall be made at 25°C +5°C ambient atmos-
pheric pressure and humidity.
4.3.2 Test equipment and inspection facilities—Test
equipment and inspection facilities shall be of sufficient
accuracy and quality to permit performance of the required
inspection. The manufacturer shall establish calibration of
inspection equipment to the satisfaction of the user but at a
minimum must meet the requirements of MIL-STD-45662.
4.4 Acceptance inspection
4.4.1 Acceptance tests—Acceptance tests shall consist of
Group A. Capacitors shall be subjected to Group A
(Subgroups 1, 2, 3), and C. Testing in accordance with
Group C shall be considered degrading and product so tested
shall not be shipped.
a)Weibull distribution plot
b)Failure rate computation sheet
a) Acceptance inspection (see 4.4)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 [phone] • www.kemet.com
GR500 GRADED RELIABILITY SPECIFICATION (Continued)
GR500 GRADED RELIABILITY SPECIFICATIONS
4.4.1.1 Group A—Group A shall consist of those tests listed
in Table 2.
4.4.1.2 Group C—Group C shall consist of those tests listed
in Table 3.
4.4.1.2.1 Sampling Plan—Group C shall be performed
every three months. The sample shall consist of 48 pieces,
selected at random from the largest and smallest case sizes
produced during the month in the approximately ratio of
production.
4.4.1.2.2 Nonconformance—Failures in excess of those
allowed during Group C testing shall be cause to discontinue
acceptance of product. Corrective action sha1l be instituted
and the product retested. Evidence of successful corrective
action shall release the product for acceptance.
4.5 Test procedures
Test
Subgroup 1
Subgroup 2
Subgroup 3
Test
Subgroup 1
Subgroup 2
Subgroup 3
Thermal shock
Surge current
Grading (Accelerated
DC Leakage
Capacitance
Dissipation Factor
ESR
Seal
Radiographic
Visual & mechanical
Solderability
Temperature stability
Shock
Vibration
Thermal shock
Terminal strength
Resistance to solvents
Resistance to
Moisture resistance
Sleeving
Life (at 125°C)
voltage aging
inspection
inspection
and immersion
soldering heat
Per Production Lot of a single capacitance value, case size and voltage.
TABLE 2 — Group A Inspection
TABLE 3 — Group C Inspection
Requirement
Requirement
Paragraph References
Paragraph References
3.5.1.9
3.5.13
3.5.17
3.5.10
3.5.11
3.5.12
3.5.14
3.5.20
3.5.21
3.5.15
3.5.16
3.5.19
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
3.5.6
3.5.7
3.5.8
3.5.9
Method
Method
4.5.18
4.5.17
4.5.12
4.5.16
4.5.10
4.5.13
4.5.19
4.5.20
4.5.14
4.5.15
4.5.18
4.5.11
4.5.2
4.5.3
4.5.4
4.5.5
4.5.6
4.5.7
4.5.8
4.5.1
4.5.9
pieces tested
pieces tested
Number of
Number of
100%
13
20
12
12
24
Allowed
Allowed
Failures
Failures
appli-
cable
Not
0
0
1