TISP70XXF3 Bourns Electronic Solutions, TISP70XXF3 Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
TISP70XXF3
Manufacturer Part Number
TISP70XXF3
Description
LOW-VOLTAGE TRIPLE ELEMENT BIDIRECTIONAL THYRISTOR OVERVOLTAGE PROTECTORS
Manufacturer
Bourns Electronic Solutions
Datasheet
1.TISP70XXF3.pdf
(16 pages)
www.DataSheet4U.com
DataSheet U .com
To verify the withstand capability and safety of the equipment, standards require that the equipment is tested with various impulse wave forms.
The table in this section shows some common test values.
Manufacturers are being increasingly required to design in protection coordination. This means that each protector is operated at its design
level and currents are diverted through the appropriate protector, e.g.,the primary level current through the primary protector and lower levels
of current may be diverted through the secondary or inherent equipment protection. Without coordination, primary level currents could pass
through the equipment only designed to pass secondary level currents. To ensure coordination happens with fixed voltage protectors, some
resistance is normally used between the primary and secondary protection (R1a and R1b, Figure 21). The values given in this data sheet apply
to a 400 V (d.c. sparkover) gas discharge tube primary protector and the appropriate test voltage when the equipment is tested with a primary
protector.
If the impulse generator current exceeds the protector’s current rating, then a series resistance can be used to reduce the current to the
protector’s rated value to prevent possible failure. The required value of series resistance for a given waveform is given by the following
calculations. First, the minimum total circuit impedance is found by dividing the impulse generator’s peak voltage by the protector’s rated
current. The impulse generator’s fictive impedance (generator’s peak voltage divided by peak short circuit current) is then subtracted from the
minimum total circuit impedance to give the required value of series resistance. In some cases, the equipment will require verification over a
temperature range. By using the derated waveform values from the thermal information section, the appropriate series resistor value can be
calculated for ambient temperatures in the range of 0 °C to 70 °C.
1.2/50 Generators (continued)
Impulse Testing
Specifications are subject to change without notice.
Customers should verify actual device performance in their specific applications.
ITU-T K.20/K.21
MARCH 1994 - REVISED MARCH 2006
4
† FCC Part 68 terminology for the waveforms produced by the ITU-T recommendation K.21 10/700 impulse generator
NA = Not Applicable, primary protection removed or not specified.
GR-1089-CORE
Lightning Surge (continued)
(March 1998)
FCC Part 68
Standard
I 31-24
TISP70xxF3 (LV) Overvoltage Protector Series
Peak Voltage
Setting
2500
1000
1500
1000
1500
1500
1500
1000
1500
4000
4000
800
V
Waveform
1 µF
(SINGLE)
(SINGLE)
(SINGLE)
C
10/1000
Voltage
9/720 †
0.5/700
10/160
10/560
(DUAL)
10/700
(DUAL)
1
1 kV
2/10
V
µs
C
SW
76 Ω
APPLICATIONS INFORMATION
R
Peak Current
1
K.22 1.2/50 GENERATOR
2 x 500
2 x 100
2 x 27
2 x 72
Value
37.5
37.5
37.5
200
100
100
25
25
A
Figure 19.
13 Ω
R
2
30 nF
C
2
Waveform
NOTE: SOME STANDARDS
10/1000
Current
5/320 †
5/320 †
0.2/310
10/160
10/560
4/250
5/310
5/310
5/310
4/250
2/10
µs
CAPACITORS WITH
REPLACE OUTPUT
25 Ω RESISTORS
8 nF
8 nF
C
C
4
3
25 °C Rating
TISP7xxxF3
2 x 190
2 x 45
2 x 95
2 x 95
110
50
70
70
70
70
70
70
A
Resistance
Series
12
17
Ω
6
8
0
0
0
0
0
Coordination
Resistance
Ω (Min.)
NA
NA
NA
NA
NA
6
6