T315XW01V2 AUO, T315XW01V2 Datasheet

Page 1

... Product Description: AUO Model Name: T315XW01 V2 Customer Part No/Project Name Customer Signature Please return one copy with your signature and comments for our confirmation. AU Optronics Corporation Tel: +886-3-563-2899 Fax: +886-3-566-5233 ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed ...

Page 2

AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed Product Specifications 31.5” WXGA Color TFT-LCD Module Model Name: T315XW01 Preliminary Specifications (*) Final Specifications T315XW01 V2 - Specs. Ver 1.1 2/25 ...

Page 3

No COVER CONTENTS RECORD OF REVISIONS 1 GENERAL DESCRIPTION 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL SPECIFICATIONS 3-1 ELECTRICAL CHARACTREISTICS 3-2 INTERFACE CONNECTIONS 3-3 SIGNAL TIMING SPECIFICATIONS 3-4 SIGNAL TIMING WAVEFORMS 3-5 COLOR INPUT DATA REFERNECE 3-6 POWER SEQUENCE 4 OPTICAL ...

Page 4

Version Date No 0.1 2005/3/14 All 1.0 2005/5/4 1 Preliminary specs 1.1 2005/6/6 15 G/G response time max : 35ms ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed Record of Revision Old Description All ...

Page 5

General Description This specification applies to the 31.51 inch Color TFT-LCD Module T315XW01 V2. This LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 31.51 inch. This module supports 1366x768 XGA-WIDE ...

Page 6

Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause permanent damage to the unit. Item Logic/LCD Drive Voltage Input Voltage of Signal BLU Input Voltage BLU Brightness Control Voltage Operating Temperature Operating Humidity Storage Temperature ...

Page 7

Electrical Specification The T315XW01 V2 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the BLU power inverter.. 3-1 Electrical ...

Page 8

Interface Connections - LCD connector (CN3): JAE FI-E30S or equivalent - LVDS Transmitter: SN75LVDS83(Texas Instruments) or equivalent Note: 1. All GND (ground) pins should be connected together and should also be connected to the LCD’s metal frame. All Vcc ...

Page 9

LVDS Option = L (GND) Previous Cycle Clock RIN0 RIN0- RIN1 RIN1- RIN2 RIN2- RIN3 RIN3- LVDS Option = H (3.3V) Previous Cycle Clock RIN0 ...

Page 10

BACKLIGHT CONNECTOR PIN CONFIGURATION Item Input Voltage Input Current Input Power Inrush Current, 0.3ms Output Frequency On/Off Control Voltage On/Off Control Current Dimming Control Voltage Dimming Control Current External PWM Control Voltage External PWM Control Current External PWM Duty Ratio ...

Page 11

Signal Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation. * Timing Table DE only Mode ...

Page 12

Signal Timing Waveforms ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V2 - Specs. Ver 1.1 12/25 ...

Page 13

Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below ...

Page 14

Power Sequence Power Supply For LCD 10% V (+5V) & VDDB dd GND Interface Signal GND Power For LAMP (BLON) Parameter (1) Apply the lamp voltage within the LCD operation range. When ...

Page 15

Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 45 minutes in a dark environment at 25℃. The values specified are at an approximate distance 50cm from the LCD surface at a ...

Page 16

Note: 1. Contrast Ratio (CR) is defined mathematically as: Contrast Ratio= 2. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2. When ...

Page 17

FIG.3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal. L0,15,L31,….L255 100% 90% 10 FIG.4 Viewing angle ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No ...

Page 18

Mechanical Characteristics The contents provide general mechanical characteristics for the model T315XW01 V2. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Bezel Opening Active Display Area Weight Surface Treatment ©Copyright ...

Page 19

Front View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V2 - Specs. Ver 1.1 19/25 ...

Page 20

Rear View ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V2 - Specs. Ver 1.1 20/25 ...

Page 21

Reliability Environment test condition No 1 High temperature storage test 2 Low temperature storage test 3 High temperature operation test 4 Low temperature operation test 5 Vibration test (non-operating) 6 Shock test (non-operating) 7 Vibration test (with carton) 8 ...

Page 22

International Standard 7-1. Safety (1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995 Standard for Safety of Information Technology Equipment Including electrical Business Equipment. (2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association, Standard for Safety of ...

Page 23

Packing Label : 83mm * 23mm Carton Label : 80mm * 40mm AU O ptronics MODEL NO: T315XW01 VX PART NO: 9731T01.XXX CUSTOMER NO: CARTON NO: *PM100-01A1600001* Made in Taiwan ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. ...

Page 24

Carton : 3pcs Modules 947(L)mm * 290(W)mm * 595(H)mm ©Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed T315XW01 V2 - Specs. Ver 1.1 24/25 ...

Page 25

PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1 MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure ...

Page 26

ELECTROSTATIC DISCHARGE CONTROL Since a module is composed of electronic circuits not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly. 9-4 PRECAUTIONS ...