IDT71016S Integrated Device Technology, IDT71016S Datasheet - Page 6
![no-image](/images/no-image-200.jpg)
IDT71016S
Manufacturer Part Number
IDT71016S
Description
64k X 16 Static Ram
Manufacturer
Integrated Device Technology
Datasheet
1.IDT71016S.pdf
(9 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IDT71016S-15Y8
Manufacturer:
IDT
Quantity:
6 500
Part Number:
IDT71016S12PH
Manufacturer:
IDT
Quantity:
20 000
Company:
Part Number:
IDT71016S12PHG
Manufacturer:
IDT10
Quantity:
232
Company:
Part Number:
IDT71016S12Y
Manufacturer:
IDT22
Quantity:
136
Company:
Part Number:
IDT71016S15PH
Manufacturer:
IDT
Quantity:
6 000
Company:
Part Number:
IDT71016S15PH
Manufacturer:
IDT
Quantity:
66
Part Number:
IDT71016S15PH
Manufacturer:
IDT
Quantity:
20 000
Part Number:
IDT71016S15PHGI
Manufacturer:
IDT
Quantity:
20 000
Part Number:
IDT71016S15Y
Manufacturer:
IDT
Quantity:
20 000
Timing Waveform of Read Cycle No. 2
NOTES:
1. WE is HIGH for Read Cycle.
2. Address must be valid prior to or coincident with the later of CS, BHE, or BLE transition LOW; otherwise t
3. Transition is measured ±200mV from steady state.
Timing Waveform of Write Cycle No. 1 (WE Controlled Timing)
NOTES:
1. A write occurs during the overlap of a LOW CS, LOW BHE or BLE, and a LOW WE.
2. OE is continuously HIGH. If during a WE controlled write cycle OE is LOW, t
3. During this period, I/O pins are in the output state, and input signals must not be applied.
4. If the CS LOW or BHE and BLE LOW transition occurs simultaneously with or after the WE LOW transition, the outputs remain in a high-impedance state.
5. Transition is measured ±200mV from steady state.
IDT71016, CMOS Static RAM
1 Meg (64K x 16-bit)
BHE, BLE
ADDRESS
ADDRESS
BHE
DATA
data to be placed on the bus for the required t
minimum write pulse is as short as the specified t
DATA
DATA
,
BLE
WE
OUT
CS
OE
OUT
CS
IN
PREVIOUS DATA VALID
t
AS
DW
. If OE is HIGH during a WE controlled write cycle, this requirement does not apply and the
WP
t
.
CLZ
(3)
(3)
t
WHZ
t
ACS
t
t
t
AW
BLZ
AA
(5)
t
CW
t
(2)
BE
(3)
t
OLZ
(2)
t
t
(2)
BW
WC
t
RC
(3)
6.42
WP
t
6
OE
t
WP
must be greater than or equal to t
(1)
DATA
t
DW
IN
Commercial and Industrial Temperature Ranges
VALID
DATA
AA
t
DH
t
t
is the limiting parameter.
OW
WR
OUT
(5)
WHZ
+ t
VALID
t
OH
DW
t
CHZ
t
BHZ
t
to allow the I/O drivers to turn off and
OHZ
(3)
(3)
DATA VALID
(3)
t
t
CHZ
BHZ
(5)
(1,2,4)
(5)
3210 drw 08
3210 drw 07
,
,