AAT4621ITP-T1 AnalogicTech, AAT4621ITP-T1 Datasheet
AAT4621ITP-T1
Related parts for AAT4621ITP-T1
AAT4621ITP-T1 Summary of contents
Page 1
General Description The AAT4621 SmartSwitch is a current limited P- channel MOSFET power switch designed for high- side load-switching applications in PC Card GSM/GPRS/3G modem cards. Used in conjunc- tion with a super capacitor, the AAT4621 will ensure that the ...
Page 2
Pin Descriptions Pin # Symbol TSOPJW-12 TDFN33- GND 10, 11 VCC OUT 9 4 ISETL 10 3 ISETU 11 2 ...
Page 3
Absolute Maximum Ratings Symbol Description V VCC to GND GND SET, OUT to GND SET OUT I Maximum Continuous Switch Current MAX Thermal Characteristics Symbol Description θ Maximum Thermal Resistance JA P ...
Page 4
Electrical Characteristics V = 3.0V to 5.5V -40°C to 85°C unless otherwise noted. Typical values are Symbol Description V Operation Voltage CC I Quiescent Current Q I Quiescent Current U QU0 0 I Off ...
Page 5
Typical Characteristics Output Current vs. Output Voltage = 249KΩ Ω 25°C) (R SETU 0.30 0. 0.20 0.15 0. 3.3V IN 0.05 0.00 0 0.5 1 1.5 2 2.5 3 Output Voltage (V) Reverse ...
Page 6
Typical Characteristics R vs. Input Voltage DS(ON) = 0kΩ Ω SET 2.5 3 3.5 4 Input Voltage (V) V vs. R RHYS RHYS 2.00 1.80 1.60 1.40 1.20 1.00 0.80 0.60 0.40 ...
Page 7
Typical Characteristics V and V vs. Input Voltage IH IL (ENUB = Open; Vary ENLB 25°C) 1 1.0 0.9 0 0.7 0.6 2.5 3.5 4.5 5.5 Input Voltage (V) Soft Short Circuit with 5Ω ...
Page 8
Typical Characteristics Charging Profile (I = 150mA 4.5V; C LIMIT OUT OUT Time (5s/div) GSM900 GPRS Class 12 Transmit 1-Slot Ch975, 33dBm V = 3.83V 3.80V OUT I ...
Page 9
Functional Block Diagram VCC Under- Voltage Lockout 1.2V Reference GND Functional Description The AAT4621 is an integrated P-channel MOSFET load switch with an upper and lower adjustable cur- rent limits which can be enabled independently, over ...
Page 10
SET pins and ground. The minimum current limit threshold is specified the load condition maintains LIM(MIN) the device in current limit and the chip temperature reaches a critical point, then ...
Page 11
I vs. R and R LOAD SETU 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0.10 0.30 0.50 0.70 0.90 (MΩ Ω and R SETU SETL Figure 1: Calculated Current Limit R Characteristic. System Ready Hysteresis (RHYS) and System ...
Page 12
Digitally Programmed Soft Start Current Limit At turn on, the digital soft start increases the load current in discrete levels equal to 1/32 of the final programmed current limit set point from zero to the final programmed current limit level. ...
Page 13
Figure 3: AAT4621 TSOPJW-12 Evaluation Board PCB Top Side. Figure 4: AAT4621 TSOPJW-12 Evaluation Board PCB Bottom Side. 4621.2007.07.1.0 AAT4621 PC Card Current Limit Interface and Capacitor Charger 13 ...
Page 14
Figure 5: AAT4621 TDFN33-14 Evaluation Board PCB Top Side Figure 6: AAT4621 TDFN33-14 Evaluation Board PCB Bottom Side 14 AAT4621 PC Card Current Limit Interface and Capacitor Charger 4621.2007.07.1.0 ...
Page 15
... A solder fillet at the exposed copper edge cannot be guaranteed and is not required to ensure a proper bottom solder connection. 4621.2007.07.1.0 PC Card Current Limit Interface Marking 1 YWXYY TSOPJW-12 + 0.10 0.20 - 0.05 7° NOM 4° ± 4° 0.055 ± 0.045 0.010 AAT4621 and Capacitor Charger Part Number (Tape and Reel) 2 AAT4621ITP-T1 AAT4621IWO-T1 0.04 REF 0.45 ± 0.1 5 2.75 ± 0.25 15 ...
Page 16
... AnalogicTech cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in an AnalogicTech product. No circuit patent licenses, copyrights, mask work rights, or other intellectual property rights are implied. AnalogicTech reserves the right to make changes to their products or specifications or to discontinue any product or service with- out notice. Except as provided in AnalogicTech’ ...