MCP6546T-I/P Microchip Technology, MCP6546T-I/P Datasheet - Page 2

• Manufacturer Part Number: MCP6546T-I/P
• Description: Push-Pull Output Sub-Microamp Comparator
• Manufacturer: Microchip Technology

MCP6546/7/8/9
1.0
1.1
V
Open Drain output................................................. V
All inputs and outputs ........................ V
Difference Input voltage .........................................|V
Output Short Circuit Current ..................................continuous
Current at Input Pins ....................................................±2 mA
Current at Output and Supply Pins ............................±30 mA
Storage temperature .....................................-65°C to +150°C
Ambient temp. with power applied ................-55°C to +125°C
Junction temp..............................................................+150°C
ESD protection on all pins (HBM); (MM) ................4 kV; 400V
DC CHARACTERISTICS
DS21714A-page 2
Unless otherwise indicated, all limits are specified for: V
R
Power Supply:
Supply Voltage
Quiescent Current per comparator
Input:
Input Voltage Range
Common-Mode Rejection Ratio
Common-Mode Rejection Ratio
Common-Mode Rejection Ratio
Power Supply Rejection Ratio
Input Offset Voltage
Input Hysteresis Voltage
Input Bias Current
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Open Drain Output:
Output Pull-Up Voltage
High Level Output Current
Low Level Output Voltage
Short Circuit Current
Output Pin Capacitance
Note 1:
DD
PU
Drift with Temperature
Drift with Temperature
Drift with Temperature
Over Temperature
- V
= 2.74 k to V
2:
SS
...........................................................................7.0V
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings*
The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the
input-referred trip points.
Do not short the output about V
does not function properly when V
Parameters
PU
= V
DD
. Refer to Figure 1-3.
V
V
ss
CMRR
CMRR
CMRR
PSRR
Sym
V
V
V
Z
C
HYST
HYST
V
Z
V
V
V
I
OS
I
HYST
–0.3V to V
DIFF
I
I
CMR
I
I
OS
OH
OUT
CM
SC
SS
DD
Q
OS
PU
OL
B
B
/ T
/ T
/ T
+10V. Limit the output current to Absolute Maximum Rating of 30 mA. The comparator
PU
< V
V
SS
SS
-100
DD
Min
-7.0
V
1.6
0.3
1.5
V
DD
55
50
55
63
—
—
—
—
—
—
—
—
—
—
DD
DD
SS
.
+10.5V
0.3
+0.3V
- V
DD
SS
= +1.6V to +5.5V, V
10
10
|
±1.5
Typ
±50
0.6
3.3
70
65
70
80
—
—
—
—
—
—
±3
10
±1
13
13
1
8
5
||4
||2
V
V
Max
DD
SS
+7.0
*Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
PIN FUNCTION TABLE
100
5.5
1.0
6.5
10
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+IN/+INA/+INB/+INC/+IND
-IN/-INA/-INB/-INC/-IND
V
V
OUT/OUTA/OUTB/OUTC/OUTD Outputs
CS
+0.3
+0.2
DD
ss
SS
Units
µV/°C T
µV/°C T
µV/°C T
mV
mV
mA
µA
dB
dB
dB
dB
pA
pA
pA
nA
= GND, T
pF
||pF
||pF
V
V
V
V
NAME
I
V
V
V
V
V
V
V
T
V
(Note 2)
V
I
V
OUT
OUT
A
A
A
A
DD
DD
DD
CM
CM
CM
CM
CM
DD
PU
= -40°C to +85°C, V
= -40°C to +25°C, V
= +25°C to +85°C, V
= -40°C to +85°C, V
A
= V
= 0
= 5V, V
= 5V, V
= 5V, V
= V
= V
= V
= V
= V
= 1.6V to 5.5V, V
= 2 mA, V
= 25°C, V
SS
SS
DD
SS
SS
SS
(Note 1)
(Note 1)
= 5.0V (Note 2)
CM
CM
CM
2002 Microchip Technology Inc.
IN
PU
= -0.3V to 5.3V
= 2.5V to 5.3V
= -0.3V to 2.5V
Conditions
+
= V
= V
Non-inverting Inputs
Inverting Inputs
Positive Power Supply
Negative Power Supply
Chip Select
DD
DD
PU
CM
CM
CM
/2, V
= 5V
CM
= 10V (Note 2)
FUNCTION
= V
= V
= V
= V
IN
-
SS
SS
SS
SS
= V
SS
,