NCP1086 ON, NCP1086 Datasheet
![no-image](/images/no-image-200.jpg)
NCP1086
Available stocks
Related parts for NCP1086
NCP1086 Summary of contents
Page 1
... A Adjustable and 3.3 V Fixed Output Linear Regulator The NCP1086 linear regulator provides 1 3 adjustable output voltage. The adjustable output voltage device uses two external resistors to set the output voltage within a 1. 5.5 V range. The regulators is intended for use as post regulator and microprocessor supply ...
Page 2
... The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider used to set the output voltage is selected to meet the minimum requirement. 7. Guaranteed by design, not 100% tested in production. 8. Thermal shutdown is 100% functionally tested in production. NCP1086 Parameter Wave Solder (through hole styles only) Note 1 Reflow (SMD styles only) Note 2 ...
Page 3
... TO−220−3 SOT−223 Thermal − + Error Shutdown Amplifier Bandgap Figure 3. Block Diagram, Adjustable Output NCP1086 = 10 mF Tantalum OUT = 1.5 A.) full load Test Conditions f = 120 Hz 1 − 3.0 V; OUT IN OUT V = 1.0 V RIPPLE P−P − − ...
Page 4
... OUT OUT IN = 0.1 mF −200 C Adj 1500 750 0 0 1.0 2.0 3.0 4.0 5.0 6.0 Time, ms Figure 9. Transient Response (Adjustable Output) NCP1086 0.10 0.08 0.04 0.00 −0.04 −0.08 −0.12 1200 1500 100 110 120 130 Figure 6. Reference Voltage vs. Temperature 3.5 3.1 2.7 2.3 1.9 1.5 100 120 1.0 2.0 Figure 8. Short Circuit Current vs V ...
Page 5
... V output voltages at currents up to 1.5 A. The regulator is protected against overcurrent conditions and includes thermal shutdown. The NCP1086 series has a composite PNP−NPN output transistor and requires an output capacitor for stability. A detailed procedure for selecting this capacitor is included in the Stability Considerations section. ...
Page 6
... tantalum capacitor will work for most reaches the point at applications, but with high current regulators such as the NCP1086 series the transient response and stability improve with higher values of capacitance. The majority of applications for this regulator involve large changes in load current, so the output capacitor must supply the instantaneous load current ...
Page 7
... GND Figure 18. Protection Diode Scheme for Large Output Capacitors (3.3 V Fixed Output) Output Voltage Sensing Since the NCP1086 is a three terminal regulator not possible to provide true remote load sensing. Load regulation is limited by the resistance of the conductors connecting the regulator to the load. ...
Page 8
... R QJA + R QJC ) R QCS ) R QSA The value for R result can be substituted in Equation 1. The value for R regulator such as the NCP1086 the majority of the heat is generated in the power transistor section. The value for R depends on the heatsink type, while R qSA factors such as package type, heatsink interface (is an (eq ...
Page 9
... Adjustable NCP1086D2T−ADJR4G Adjustable NCP1086ST−ADJT3 Adjustable NCP1086T−33 3.3 V NCP1086D2T−33 3.3 V NCP1086D2T−33R4 3.3 V NCP1086D2T−33R4G 3.3 V NCP1086ST−33T3 3.3 V †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. NCP1086 Package TO− ...
Page 10
... CASE 221A CASE 418AB CASE 318E AYW 086−A NCP1086−A AWLYWW NCP1086−A 1 AWLYWW WL, L YY Work Week NCP1086 MARKING DIAGRAMS 3.3 V Fixed Output TO−220−3 T SUFFIX CASE 221A 1086−33 AWLYWW 1 = Assembly Location = Wafer Lot = Year http://onsemi.com PAK− ...
Page 11
... F −B− −Y− 0.25 (0.010 NCP1086 PACKAGE DIMENSIONS TO−220−3 T SUFFIX CASE 221A−08 ISSUE AA SEATING −T− PLANE http://onsemi.com 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. ...
Page 12
... −A− C NCP1086 PACKAGE DIMENSIONS 2 D PAK−3 CASE 418AB−01 ISSUE O TERMINAL http://onsemi.com 12 NOTES: 1. DIMENSIONS AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH AND METAL BURRS. ...
Page 13
... 0.08 (0003) H SOLDERING FOOTPRINT 2.0 0.079 2.0 0.079 PACKAGE THERMAL DATA Parameter R Typical qJC R Typical qJA * Depending on thermal properties of substrate. R NCP1086 SOT−223 ST SUFFIX CASE 318E−04 ISSUE K NOTES: 6. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 7. CONTROLLING DIMENSION: INCH. DIM 3.8 0.15 6.3 2.3 2.3 0.248 0.091 ...
Page 14
... P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: orderlit@onsemi.com NCP1086 N. American Technical Support: 800−282−9855 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center 2− ...