IDT72V3642L10PF IDT, Integrated Device Technology Inc, IDT72V3642L10PF Datasheet - Page 13

• Manufacturer Part Number: IDT72V3642L10PF
• Description: IC FIFO SYNC 3.3V CMOS 120-TQFP
• Manufacturer: IDT, Integrated Device Technology Inc
• Series: 72Vr

Specifications of IDT72V3642L10PF

• Function: Synchronous
• Memory Size: 72M (1M x 72)
• Data Rate: 100MHz
• Access Time: 10ns
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 120-TQFP, 120-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 72V3642L10PF; 800-1534

writes data to its array. For both FWFT and IDT Standard modes, each time
a word is written to a FIFO, its write pointer is incremented. The state machine
that controls a Full/Input Ready flag monitors a write pointer and read pointer
comparator that indicates when the FlFO memory status is full, full-1, or full-2.
From the time a word is read from a FIFO, its previous memory location is ready
to be written to in a minimum of two cycles of the Full/Input Ready flag
synchronizing clock. Therefore, a Full/Input Ready flag is LOW if less than two
cycles of the Full/Input Ready flag synchronizing clock have elapsed since the
next memory write location has been read. The second LOW-to-HIGH
transition on the Full/Input Ready flag synchronizing clock after the read sets
the Full/Input Ready flag HIGH.
begins the first synchronization cycle of a read if the clock transition occurs at
time t
be the first synchronization cycle (see Figures 12 through 15 for FFA/IRA and
FFB/IRB timing diagrams).
ALMOST-EMPTY FLAGS (AEA, AEB)
data from its array. The state machine that controls an Almost-Empty flag monitors
a write pointer and read pointer comparator that indicates when the FIFO
memory status is almost-empty, almost-empty+1, or almost-empty+2. The
almost-empty state is defined by the contents of register X1 for AEB and register
X2 for AEA. These registers are loaded with preset values during a FIFO reset
or programmed from port A (see Almost-Empty flag and Almost-Full flag offset
programming section). An Almost-Empty flag is LOW when its FIFO contains
X or less words and is HIGH when its FIFO contains (X+1) or more words. A
data word present in the FIFO output register has been read from memory.
clock are required after a FIFO write for its Almost-Empty flag to reflect the new
level of fill. Therefore, the Almost-Full flag of a FIFO containing (X+1) or more
words remains LOW if two cycles of its synchronizing clock have not elapsed
since the write that filled the memory to the (X+1) level. An Almost-Empty flag
is set HIGH by the second LOW-to-HIGH transition of its synchronizing clock after
the FIFO write that fills memory to the (X+1) level. A LOW-to-HIGH transition of
an Almost-Empty flag synchronizing clock begins the first synchronization cycle
if it occurs at time t
Otherwise, the subsequent synchronizing clock cycle may be the first synchro-
nization cycle. (See Figures 16 and 17).
ALMOST-FULL FLAGS (AFA, AFB)
data to its array. The state machine that controls an Almost-Full flag monitors a
write pointer and read pointer comparator that indicates when the FIFO memory
status is almost-full, almost-full-1, or almost-full-2. The almost-full state is defined
IDT72V3622/72V3632/72V3642 CMOS 3.3V SyncBiFIFO
256 x 36 x 2, 512 x 36 x 2, 1,024 x 36 x 2
The Full/Input Ready flag of a FlFO is synchronized to the port clock that
A LOW-to-HIGH transition on a Full/Input Ready flag synchronizing clock
SKEW1
The Almost-Empty flag of a FIFO is synchronized to the port clock that reads
Two LOW-to-HIGH transitions of the Almost-Empty flag synchronizing
The Almost-Full flag of a FIFO is synchronized to the port clock that writes
or greater after the read. Otherwise, the subsequent clock cycle can
SKEW2
or greater after the write that fills the FIFO to (X+1) words.
TM
13
by the contents of register Y1 for AFA and register Y2 for AFB. These registers
are loaded with preset values during a FlFO reset or programmed from port
A (see Almost-Empty flag and Almost-Full flag offset programming section).
An Almost-Full flag is LOW when the number of words in its FIFO is greater than
or equal to (256-Y), (512-Y), or (1,024-Y) for the IDT72V3622, IDT72V3632,
or IDT72V3642 respectively. An Almost-Full flag is HIGH when the number
of words in its FIFO is less than or equal to [256-(Y+1)], [512-(Y+1)], or
[1,024-(Y+1)] for the IDT72V3622, IDT72V3632, or IDT72V3642 respec-
tively. Note that a data word present in the FIFO output register has been read
from memory.
are required after a FIFO read for its Almost-Full flag to reflect the new level of
fill. Therefore, the Almost-Full flag of a FIFO containing [256/512/1,024-(Y+1)]
or less words remains LOW if two cycles of its synchronizing clock have not
elapsed since the read that reduced the number of words in memory to [256/
512/1,024-(Y+1)]. An Almost-Full flag is set HIGH by the second LOW-to-HIGH
transition of its synchronizing clock after the FIFO read that reduces the number
of words in memory to [256/512/1,024-(Y+1)]. A LOW-to-HIGH transition of an
Almost-Full flag synchronizing clock begins the first synchronization cycle if it
occurs at time t
in memory to [256/512/1,024-(Y+1)]. Otherwise, the subsequent synchroniz-
ing clock cycle may be the first synchronization cycle (see Figures 18 and 19).
MAILBOX REGISTERS
information between port A and port B without putting it in queue. The Mailbox
select (MBA, MBB) inputs choose between a mail register and a FIFO for a port
data transfer operation. A LOW-to-HIGH transition on CLKA writes A0-A35 data
to the mail1 register when a port A Write is selected by CSA, W/RA, and ENA
and with MBA HIGH. A LOW-to-HIGH transition on CLKB writes B0-B35 data
to the mail2 register when a port B Write is selected by CSB, W/RB, and ENB
and with MBB HIGH. Writing data to a mail register sets its corresponding flag
(MBF1 or MBF2) LOW. Attempted writes to a mail register are ignored while
the mail flag is LOW.
FIFO output register when the port Mailbox select input is LOW and from the mail
register when the port mailbox select input is HIGH. The Mail1 Register Flag
(MBF1) is set HIGH by a LOW-to-HIGH transition on CLKB when a port B Read
is selected by CSB, W/RB, and ENB and with MBB HIGH. The Mail2 Register
Flag (MBF2) is set HIGH by a LOW-to-HIGH transition on CLKA when a port
A read is selected by CSA, W/RA, and ENA and with MBA HIGH. The data
in a mail register remains intact after it is read and changes only when new data
is written to the register. For mail register and Mail Register Flag timing diagrams,
see Figure 20 and 21.
Two LOW-to-HIGH transitions of the Almost-Full flag synchronizing clock
Each FIFO has a 36-bit bypass register to pass command and control
When data outputs of a port are active, the data on the bus comes from the
SKEW2
or greater after the read that reduces the number of words
COMMERCIAL TEMPERATURE RANGE