HT48R02N Holtek Semiconductor, HT48R02N Datasheet - Page 14
![no-image](/images/no-image-200.jpg)
HT48R02N
Manufacturer Part Number
HT48R02N
Description
(HT4xR0xx) Small Package 8-Bit OTP MCU
Manufacturer
Holtek Semiconductor
Datasheet
1.HT48R02N.pdf
(71 pages)
www.DataSheet4U.com
The following diagram illustrates the addressing/data
flow of the look-up table:
Table Program Example
The accompanying example shows how the table
pointer and table data is defined and retrieved from the
device. This example uses raw table data located in the
last page which is stored there using the ORG state-
ment. The table pointer is setup here to have an initial
value of 06H . This will ensure that the first data read
from the data table will be at the Program Memory ad-
Note:
tempreg1 db ?
tempreg2 db ?
mov a,06h
mov tblp,a
tabrdl
dec tblp
tabrdl
org 300h
dc
Rev.1.00
TABRDC [m]
TABRDL [m]
Table Read Program Example - 1K ROM size
Instruction
:
:
:
:
:
:
00Ah, 00Bh, 00Ch, 00Dh, 00Eh, 00Fh, 01Ah, 01Bh
:
:
HT46R01B/HT48R01B/HT46R01N/HT48R01N: PC9~PC8: Current program Counter bits
HT46R02B/HT48R02B/HT46R02N/HT48R02N: PC10~PC8: Current program Counter bits
@7~@0: Table Pointer TBLP bits
tempreg1
tempreg2
PC10
b10
1
; temporary register #1
; temporary register #2
; initialise table pointer - note that this address is referenced
; to the last page or present page
; transfers value in table referenced by table pointer to tempregl
; data at prog. memory address 306H transferred to tempreg1 and TBLH
; reduce value of table pointer by one
; transfers value in table referenced by table pointer to tempreg2
; data at prog.memory address 305H transferred to tempreg2 and TBLH
; in this example the data 1AH is transferred to
; tempreg1 and data 0FH to register tempreg2
; the value 00H will be transferred to the high byte register TBLH
; sets initial address of last page
PC9
b9
1
PC8
b8
1
@7
@7
b7
Table Location
@6
@6
Table Location Bits
b6
14
dress F06H or 6 locations after the start of the last
page. Note that the value for the table pointer is refer-
enced to the first address of the present page if the
of the table data which in this case is equal to zero will
be transferred to the TBLH register automatically when
the TABRDL [m] instruction is executed.
Because the TBLH register is a read-only register and
cannot be restored, care should be taken to ensure its
protection if both the main routine and Interrupt Service
Routine use the table read instructions. If using the table
read instructions, the Interrupt Service Routines may
change the value of TBLH and subsequently cause er-
rors if used again by the main routine. As a rule it is rec-
ommended that simultaneous use of the table read
instructions should be avoided. However, in situations
where simultaneous use cannot be avoided, the inter-
rupts should be disabled prior to the execution of any
main routine table-read instructions. Note that all table
related instructions require two instruction cycles to
complete their operation.
TABRDC [m] instruction is being used. The high byte
@5
@5
b5
@4
@4
b4
HT46R01B/02B/01N/02N
HT48R01B/02B/01N/02N
@3
@3
b3
@2
@2
b2
December 15, 2009
@1
@1
b1
@0
@0
b0