83C196MC Intel Corporation, 83C196MC Datasheet
![no-image](/images/manufacturer_photos/0/3/337/intel_corporation_sml.jpg)
83C196MC
Related parts for 83C196MC
83C196MC Summary of contents
Page 1
... Note that the 64-L SDIP package does not include and the CLKOUT pins Operational characteristics are guaranteed over the temperature range of The 87C196MC contains 16 Kbytes on-chip OTPROM The 83C196MC contains 16 Kbytes on-chip ROM All references to the 80C196MC also refers to the 83C196MC and 87C196MC unless noted ...
Page 2
NOTE Connections between the standard I O ports and the bus are not shown Figure 1 87C196MC Block Diagram 2 270946 – 1 ...
Page 3
PROCESS INFORMATION This device is manufactured on PX29 5 a CHMOS III-E process Additional process and reliability infor- mation is available in Intel’s Components Quality and Reliability Handbook Order Number 210997 EXAMPLE N87C196MC is 84-Lead PLCC OTPROM 16 MHz For ...
Page 4
NOTE The pin sequence is correct The 64-Lead SDIP package does not include the following pins P1 4 ACH12 P2 7 COMPARE3 P5 1 INST CLKOUT Figure 2 64-Lead Shrink DIP (SDIP) Package 4 270946 –2 ...
Page 5
NOTE NC means No Connect Do not connect these pins Figure 3 84-Lead PLCC Package 8XC196MC 270946 – ...
Page 6
NOTE NC means No Connect Do not connect these pins Figure 4 80-Lead Shrink EIAJQFP (Quad Flat Pack) 6 270946 – 4 ...
Page 7
PIN DESCRIPTIONS (Alphabetically Ordered) Symbol ACH0–ACH12 Analog inputs to the on-chip A D converter ACH0 – 7 share the input pins (P0 0– 0– with P0 0– 7 and ACH8 – 12 share pins with P1 ...
Page 8
PIN DESCRIPTIONS (Alphabetically Ordered) (Continued) Symbol PORT6 8-bit output port P6 6 and P6 7 output PWM the others are used as the Wave Form Generator outputs Can be used as standard output ports PWM0 PWM1 Programmable duty cycle ...
Page 9
ABSOLUTE MAXIMUM RATINGS Ambient Temperature Under Bias Storage Temperature Voltage from ANGND SS Voltage ANGND b SS ...
Page 10
DC ELECTRICAL CHARACTERISTICS Symbol Parameter I Input Leakage Current on All Input LI Only Pins I Input Leakage Current on Port0 LI1 and Port1 I Input Low Current on BD Ports IL (Note 1) I Input Low Current on ...
Page 11
EXPLANATION OF AC SYMBOLS Each symbol is two pairs of letters prefixed by ‘‘T’’ for time The characters in a pair indicate a signal and its condition respectively Symbols represent the time between the two signal condition points Conditions Signals ...
Page 12
AC ELECTRICAL CHARACTERISTICS Test Conditions Capacitive load on all pins The 87C196MC will meet the following timing specifications Symbol Parameter T XTAL1 to CLKOUT High or Low XHCH T CLKOUT Cycle Time CLCL T CLKOUT High Period CHCL T ...
Page 13
SYSTEM BUS TIMINGS 8XC196MC 270946 – ...
Page 14
READY TIMINGS (One Wait State) BUSWIDTH TIMINGS 14 270946 – 6 270946 – 7 ...
Page 15
EXTERNAL CLOCK DRIVE Symbol Parameter 1 T Oscillator Frequency XLXL T Oscillator Period XLXL T High Time XHXX T Low Time XLXX T Rise Time XLXH T Fall Time XHXL EXTERNAL CRYSTAL CONNECTIONS NOTE Keep oscillator components close to chip ...
Page 16
CHARACTERISTICS The sample and conversion time of the A D convert the 8-bit or 10-bit modes is programmed by loading a byte into the AD TIME Special Function Register This allows optimizing the A ...
Page 17
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should nominally ...
Page 18
MODE A D OPERATING CONDITIONS Symbol Description T Ambient Temperature A V Digital Supply Voltage CC V Analog Supply Voltage REF T Sample Time SAM T Conversion Time CONV F Oscillator Frequency OSC NOTES ANGND and V should ...
Page 19
EPROM SPECIFICATIONS OPERATING CONDITIONS Symbol Description T Ambient Temperature during Programming A V Supply Voltage during Programming CC V Reference Supply Voltage during Programming REF V Programming Voltage Pin Voltage EA F Oscillator Frequency during Auto OSC ...
Page 20
DC EPROM PROGRAMMING CHARACTERISTICS Symbol Parameter I V Supply Current (When Programming NOTE Do not apply V until V is stable and within specifications and the oscillator clock has stabilized or the device may ...
Page 21
SLAVE PROGRAMMING MODE IN WORD DUMP WITH AUTO INCREMENT NOTE P3 0 must be low (‘‘0’’) SLAVE PROGRAMMING MODE TIMING IN DATA PROGRAM WITH REPEATED PROG PULSE AND AUTO INCREMENT 8XC196MC 270946 –12 270946 –13 21 ...
Page 22
... The following important differences exist between this data sheet (270946-002) and the previous ver- sion (270946-003) 1 The data sheet was reorganized to standard for- mat 2 Added 83C196MC device 3 Added package thermal characteristics 4 Added note on missing pins on SDIP package 5 Removed SFR maps (now in user’s manual) 6 Added note on T ...