RF6263 RF Micro Devices, RF6263 Datasheet
RF6263
Related parts for RF6263
RF6263 Summary of contents
Page 1
... RF amplifier in 3V IS-95/CDMA2000-1X/ AMPS handheld digital cellular equipment, spread-spectrum systems, and other applications in the 824MHz to 849MHz band. The RF6263 has a digital control pin which when enabled will allow the amplifier to operate up to 19dBm output power with reduced current consumption. The low power mode current consumption can be reduced by more than 50% that of a standard power amplifier ...
Page 2
... RF6263 Absolute Maximum Ratings Parameter Supply Voltage (RF off) ≤31dBm) Supply Voltage (P OUT Control Voltage (V ) REG Input RF Power Mode Voltage (V ) MODE Operating Temperature Storage Temperature Moisture Sensitivity Level (IPC/JEDEC J-STD-20) Parameter Min. High Power Mode - CDMA (V Low) MODE Operating Frequency Range 824 ...
Page 3
... 2.5 mA 500 0.2 2.0 uA 0.5 V 2.85 2.95 V 3.0 V 0.5 V 3.0 V RF6263 Condition o T=25 C Ambient, V =3.4V, V =2.8V, CC REG V =0V, and P =30.5dBm for all param- MODE OUT eters (unless otherwise specified). V =low and V =2.8V MODE REG V =high and V =2.8V MODE REG V =high MODE High Gain Mode Low Gain Mode ...
Page 4
... RF6263 Pin Function Description connection. Do not connect this pin to any external circuit. 2 VREG Regulated voltage supply for amplifier bias circuit. In power down mode, both V and V REG 3 VMODE For nominal operation (High Power mode), V HIGH, devices are biased lower to improve efficiency. ...
Page 5
... RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A0 DS070622 C4 2200 Bias C3 2200 C40 4.7 μ DNI 100 pF R1 DNI P2 1 GND 2 GND P2-3 3 VCC1 GND 4 P2-5 VCC2 5 CON5 RF6263 OUT 2200 pF 9 C10 22 μ ...
Page 6
... RF6263 PCB Surface Finish The PCB surface finish used for RFMD’s qualification process is electroless nickel, immersion gold. Typical thickness is 3μinch to 8μinch gold over 180μinch nickel. PCB Land Pattern Recommendation PCB land patterns for PFMD components are based on IPC-7351 standards and RFMD empirical data. The pad pattern shown has been developed and tested for optimized assembly at RFMD ...
Page 7
... Thorndike Road, Greensboro, NC 27409-9421 · For sales or technical support, contact RFMD at (+1) 336-678-5570 or sales-support@rfmd.com. Rev A0 DS070622 A = 0.74 x 0.38 (mm) Typ 0.38 x 0.74 (mm) Typ 1.60 (mm) Sq. Dimensions in mm. 1.50 Typ. 0.50 Typ. Pin Pin 1 Pin 0. Pin 8 0.55 Typ. 0.75 RF6263 1.50 Typ ...
Page 8
... The following table provides useful information for carrier tape and reels used for shipping the devices described in this docu- ment. Reel RFMD Part Number Diameter Inch (mm) RF6263TR7 7 (178) QFN (Carrier Tape Drawing with Part Orientation) Notes: 1. All dimensions are in millimeters (mm). 2. Unless otherwise specified, all dimension tolerances per EIA-481. ...