DS1882 Maxim Integrated Products, DS1882 Datasheet
DS1882
Available stocks
Related parts for DS1882
DS1882 Summary of contents
Page 1
... Option 2 has 32 logarithmic steps plus mute and pro- vides software compatibility with the DS1808. When Configuration Option 2 is used in combination with the 16-pin SO package, the DS1882 is both software and pin compatible with the DS1808 in 5V applications. Notebook and PC Audio Portable Audio Equipment ...
Page 2
Dual Log Audio Digital Potentiometer ABSOLUTE MAXIMUM RATINGS Voltage SDA, and SCL Relative to GND .....-0.5V to +6. Relative Voltage on A2, A1, A0, and to GND .................-0. 0.5V), not to exceed ...
Page 3
Dual Log Audio Digital Potentiometer ANALOG POTENTIOMETER CHARACTERISTICS (V = +4.5V to +5.5V +4.5V to +7.0V -4.5V to -7.0V PARAMETER End-to-End Resistance End-to-End Resistance Tolerance Ratiometric Temperature Coefficient End-to-End Resistance Temperature Coefficient Wiper ...
Page 4
... SDA = SCL = Note crossing detection has timed out. Note 5: The DS1882 will not obstruct the SDA and SCL lines not violate their minimum and maximum input voltage levels. Note 6: Guaranteed by design. Note 7: Above Position 50, these are typical maximum. Guaranteed by characterization. ...
Page 5
Dual Log Audio Digital Potentiometer ( +5.0V -5.0V +25°C POTENTIOMETER 1 (CONFIGURATON 2) ATTENUATION vs. SETTING 0 -20.0 -40.0 -60.0 -80.0 -100 ...
Page 6
... FUNCTION 2 C communication. CONFIGURATION REGISTER INTERFACE POTENTIOMETER SETTING REGISTERS DECODER ZERO-CROSSING ZERO-CROSSING DETECTOR DETECTOR Pin Description 2 C slave address of the device slave address of the device. Block Diagram GND V- DS1882 GND V- POTENTIOMETER 1 VALUE UPDATE ...
Page 7
... When the zero-crossing detec- tion feature is not enabled, the DS1882 will allow wiper movement as soon as the DS1882 has issued the acknowledge to the master-controlling device. ...
Page 8
Dual Log Audio Digital Potentiometer Table 2. Configuration Option 2 TAP POSITION ATTENUATION (dB ...
Page 9
Dual Log Audio Digital Potentiometer Potentiometer Wiper Setting are the values of the two MSBs of the Command Byte, then the wiper settings of the poten- tiometers are to be programmed. The lower 6 LSBs of ...
Page 10
Dual Log Audio Digital Potentiometer Configuration Register entered as the value of the two MSBs of the Command Byte, then the Configuration Register modified. The three LSBs of the Configuration CONFIGURATION REGISTER Factory Default: ...
Page 11
... SLAVE ADDRESS BYTE Potentiometer 0 is the first returned from the DS1882 then followed by the value of Potentiometer 1 and then the value of the Configuration Register. Once the 8 bits of the Configuration Register have been sent, the master needs to issue an acknowledge, unless it is the last byte to be read, in which case the master issues a not acknowledge ...
Page 12
... Dual Log Audio Digital Potentiometer Writing Command Byte Values An example of writing to the DS1882 is shown in Figure 2. The DS1882 has one write command that is used to change the Potentiometer Wiper Setting Registers and the Configuration Register. All write operations begin with a START from the master, followed by a slave address byte ...
Page 13
Dual Log Audio Digital Potentiometer setup time (see Figure 4) before the next rising edge of SCL during a bit read. The device shifts out each bit of data on SDA at the falling edge of the previous SCL pulse, ...
Page 14
... It is possible to take advantage of that phenomenon by repeatedly addressing the DS1882, which allows the next page to be written as soon as the DS1882 is ready to receive the data. The alternative to acknowledge polling is to wait for a maxi bus mum period of t again to the device ...
Page 15
... Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © 2006 Maxim Integrated Products is a registered trademark of Dallas Semiconductor Corporation. Springer SDA is an open-collector output on the DS1882 that requires a pullup resistor to realize high logic levels. A master using either an open-collector output with a pullup resistor or a push-pull output driver can be uti- lized for SCL ...