MIC5016 Micrel Semiconductor, MIC5016 Datasheet - Page 9

• Manufacturer Part Number: MIC5016
• Description: Low-Cost Dual High- or Low-Side MOSFET Driver
• Manufacturer: Micrel Semiconductor

High Side Driver With Load Protection (Figure 12) Al-
though the MIC5016/17 devices are reverse battery pro-
tected, the load and power FET are not in a typical high side
configuration. In the event of a reverse battery condition, the
internal body diode of the power FET will be forward biased.
This allows the reversed supply to drive the load.
An MBR2035CT dual Schottky diode was used to eliminate
this problem. This particular diode can handle 20A continu-
ous current and 150A peak current; therefore it should survive
the rigors of an automotive environment. The diodes are
paralleled to reduce the switch loss (forward voltage drop).
MIC5016/5017
Push-Pull Driver With No Cross-Conduction (Figure 13)
As the turn-off time of the MIC5016/17 devices is much faster
than the turn-on time, a simple dual push-pull driver with no
cross conduction can be made using one MIC5016 and one
MIC5017. The same control signal is applied to both inputs;
the MIC5016 turns on with the positive signal, and the
MIC5017 turns on when it swings low.
Control Input 1
Control Input 2
Figure 12: High Side Driver WIth Load Protection
OFF
ON
Control Input
10µF
Figure 13: Push-Pull Driver
10µF
Input
Source
Gnd
V+
1/2 MIC5016
12V
12
10
14
11
12
10
14
11
3
3
V+ A
V+ B
In A
In B
Gnd
V+ A
V+ B
In A
In B
Gnd
Gate
MIC5016
MIC5017
NC
NC
NC
Source A
Source B
Source A
Source B
Gate A
Gate B
Gate A
Gate B
12V
IRFZ40
4
2
6
5
IRFZ40
4
2
6
5
IRF540
12V
MBR2035CT
IRFZ40
IRFZ40
V
V
OUT
OUT
A
B
5-154
110V AC
This scheme works with no additional components as the
relative time difference between the rise and fall times of the
MIC5014 is large. However, this does mean that there is
considerable deadtime (time when neither driver is turned
on). If this circuit is used to drive an inductive load, catch
diodes must be used on each half to provide an alternate path
for the kickback current that will flow during this deadtime.
This circuit is also a simple H-bridge which can be driven with
a PWM signal on the input for SMPS or motor drive applica-
tions in which high switching frequencies are not desired.
Synchronous Rectifier (Figure 14) In applications where
efficiency in terms of low forward voltage drops and low diode
reverse-recovery losses is critical, power FETs are used to
achieve rectification instead of a conventional diode bridge.
Here, the power FETs are used in the third quadrant of the IV
characteristic curve (FETs are installed essentially “back-
wards”). The two FETs are connected such that the top FET
turns on with the positive going AC cycle, and turns off when
it swings negative. The bottom FET operates opposite to the
top FET.
In the first quadrant of operation, the limitation of the device
is determined by breakdown voltage. Here, we are limited by
the turn-on of a parasitic p-n body drain diode. If it is allowed
to conduct, its reverse recovery time will crowbar the other
power FET and possibly destroy it. The way to prevent this
is to keep the IR drop across the device below the cut-in
voltage of this diode; this is accomplished here by using a fast
comparator to sense this voltage and feed the appropriate
signal to the control inputs of the MIC5016 device. Obviously,
it is very important to use a comparator with a fast slew rate
such as the LM393, and fast recovery diodes. 3mV of positive
feedback is used on the comparator to prevent oscillations.
At 3A, with an R
per FET is ~ 0.2 V as opposed to the 0.7 to 0.8 V drop that a
normal diode would have. Even greater savings can be had
by using FETs with lower R
that the peak currents and voltages do not exceed the SOA
of the chosen FET.
Caltronics
T126C3
25.2V
30m
Figure 14: High Efficiency 60 Hz
Synchronous Rectifier
V
CT
10k
10
10k
DS
(ON) of 0.077 , our forward voltage drop
56k
1/2 LM393
1k
DS
1N914 (2)
10µF
(ON)s, but care must be taken
1k
12
10
14
11
3
V+ A
V+ B
Gnd
In A
In B
* Parasitic body diode
MIC5016
Source A
Source B
Gate A
Gate B
1N914
1N914
4
2
6
5
October 1998
1RF540
1RF540
4700µF
*
*
Micrel
V
18V, 3A
OUT
=