CLAA154WB05AN CHUNGHWA PICTURE TUBES, CLAA154WB05AN Datasheet

Page 1

Date : 2008/04/30 CPT TFT-LCD ACCEPTED BY： APPROVED BY 黃奕凱 Prepared by : TFT-LCD Application Division Doc. No: CLAA154WB05A ...

Page 2

CPT Revision No. Date 1 2006/6/02 CPT Confidential . D a RECORD OF REVISIONS Page Tentative specification for 154WB05A was the NEW edition issued CHUNGHWA PICTURES TUBES, LTD., Description CLAA154WB05A N- www.yslcd.com.tw ...

Page 3

CPT NO. 1 OVERVIEW 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL CHARACTERISTICS 4 CONNECTOR INTERFACE PIN & FUNCTION 5 INTERFACE TIMING CHART 6 BLOCK DIAGRAM 7 MECHANICAL SPECIFICATION 8 OPTICAL CHARACTERISTICS 9 RELIABILITY TEST CONDITIONS 10 VISUAL INSPECTION SPECIFICATION 11 ...

Page 4

CPT 1. OVERVIEW CLAA154WB05A Nis 15.4” color (39.116cm) TFT-LCD (Thin Film Transistor Liquid Crystal Display) module composed of LCD panel, LVDS driver ICs, control circuit and backlight. By applying 6 bit digital data, 1280×RGB(3)×800, 262K-color images are displayed on ...

Page 5

CPT 2. ABSOLUTE MAXIMUM RATINGS The following are maximum value, which if exceeded, may cause faulty operation or damage to the unit. ITEM Power Supply Voltage for LCD Lamp voltage Lamp current Lamp frequency Operation Temperature Storage Temperature Delayed ...

Page 6

CPT 3. ELECTRICAL CHARACTERISTICS (A) TFT LCD TEM LCD POWER VOLTAGE LCD POWER CURRENT Rush CURRENT INPUT VOLTAGE COMMON LOGIC VOLTAGE ...

Page 7

CPT VCC-dip state ≧ (1)when 3.0＞VCC 2.7V (2)when VCC＜2.7V，VCC-dip condition should as the VCC-turn-off condition. [Note 2] Typical value is 0〜63 gray level.(horizontal line Pattern) 800 line mode，VCC= +3.3V Circuit condition(Typ.) VCC=3.3 V，f = Circuit condition(MAX.) ...

Page 8

CPT [Note 3] LVDS Signal Definite： – VIN-, VID = VIN + –VCM-｜, △ ｜VCM VCM = + –VID-｜, △ ｜VID VID = + –VIH-｜, VID+ =｜VIH + –VIL-｜, VID- =｜VIL + VCM =(VIN +VIN-)/2, + VCM+ =(VIH +VIH-)/2, ...

Page 9

CPT (B) BACK LIGHT (a.) ELECTRICAL CHARACTERISTICS ITEM Lamp Voltage(IL=6.0mA) Lamp Current Inverter Frequency Lamp Initial Voltage (b) LAMP LIFE – TIME ITEM LAMP LIFE-TIME (LT) Min. 15,000 Turn-on and turn-off Operation *1)Measure method：galvanometer connect to low voltage LCD ...

Page 10

CPT 4.Connector Interface PIN & Function (a) CN1(Interface signal) Outlet connector: FI-XB30SL-HF10 (JAE) ， AL2304-A0G1D-P(P-TWO) Link connector: FI-X30H (JAE, Link Type ) (Note) DDC: Display Data Requirements (Note)Refer to page6、7、8、9之 Data Mapping Pin No. SYMBOL ...

Page 11

CPT 5. INTERFACE TIMING CHART (a). LVDS input time sequence Horizontal sequence DCLK DATA (R,G, B) DENA (b) LCD input time sequence Vertical sequence LINE DATA DENA (1) Timing Chart DCLK LCD Horizontal Timing DENA Vertical CPT Confidential t ...

Page 12

CPT [Note] *1) Data is latched during DCLK falling period. *2) HD、VD is negative. *3) DENA (DATA ENABLE) usually is positive. *4) During the whole blank period, DCLK should keep input. During the vertical blank period, HD should keep ...

Page 13

CPT 6. BLOCK DIAGRAM Timing signal Display data Power BACK LIGHT CCFL CPT Confidential CHUNGHWA PICTURES TUBES, LTD G800 Power Supply Circuit INVERTER CIRCUIT (OUT SIDE) CN2 CN2 1 1 DC-AC ...

Page 14

CPT 7. MECHANICAL SPECIFICATION (1) Front side The tolerance, not show in the figure, is ±0.5mm. (2) Rear side The tolerance, not show in the figure, is ±0.5mm. CPT Confidential CHUNGHWA PICTURES TUBES, LTD., [Unit： mm] [Unit： mm] 14/ ...

Page 15

CPT 8. OPTICAL CHARACTERISTICS ITEM Contrast Ratio Luminance (5P) Uniformity(5P) Response Time Cross talk Horizont View angle al Vertical W Color R Temperature Coordinate G B These items are measured using BM-5A (TOPCON) under the dark room condition (no ...

Page 16

CPT *3) Definition of view angle(θ，ψ) Left(-) Gate Drive Side LCD Panel *4) Definition of response time *5) Crosstalk Modulation Ratio ...

Page 17

CPT 9.RELIABILITY TEST CONDITIONS (1) Temperature and Humidity High Temperature Operation High Temperature Storage High Temperature High Humidity Operation High Temperature High Humidity Storage Low Temperature Operation Low Temperature Storage Thermal Shock Temperature & Pressure Storage (2) Shock & ...

Page 18

CPT (4) Judgment standard The judgment of the above test should be made as follow: Pass ： Normal display image with no obvious non-uniformity and no line defect. Partial transformation of the module parts should be ignored. Fail：No display ...

Page 19

CPT 10. VISUAL INSPECTION SPECIFICATION 10.1 Inspection condition (1) Viewing distance is approximately cm. Viewing angle is normal to the LCD panel as figure below(10 °). (2) Ambient temperature is approximately 25 ± 5℃. (3) Ambient ...

Page 20

CPT 10.3 Inspection Criteria DEFECT TYPE VISUAL DEFECT INTERNAL ELECTRICAL DEFECT One pixel consists of 3 sub-pixels, including R,G, and B dot.(Sub-pixel = Dot) [Note1 Width[mm Length[mm Number, φ: Average Diameter [Note2] Bright ...

Page 21

CPT [Note4] Definition of distance between defect dot as following. 10.4 Handling precaution (1) Don ’ t disassemble and reassemble the module by self. (禁止自行拆解。) (2) Acid, alkali, alcohol or touched directly by hand will damage the display. (酸性、鹼性、酒精或手的直接接觸將會損傷顯示面。) ...

Page 22

CPT 11. HANDLING PRECAUTIONS FOR TFT-LCD MODULE Please pay attention to the followings in handling- TFT-LCD products; 11.1 ASSEMBLY PRECAUTION (1) Please use the mounting hole on the module side in installing and do not beading or wrenching LCD ...

Page 23

CPT 11.4 STORAGE PRECAUTIONS (1) When you store LCDs for a long time recommended to keep the temperature between 0 ℃ ~40℃ without the exposure of sunlight and to keep the humidity less than 90%RH. (2) Please ...