LP3892ES-1.2 National Semiconductor, LP3892ES-1.2 Datasheet
LP3892ES-1.2
Available stocks
Related parts for LP3892ES-1.2
LP3892ES-1.2 Summary of contents
Page 1
... At least 10 µF of input and output capacitance is required for stability. *Tantalum capacitors are recommended. Aluminum electrolytic capacitors may be used for restricted temperature range. See application hints. Connection Diagrams TO-220, Top View © 2003 National Semiconductor Corporation Features n Ultra low dropout voltage (140 mV n Low ground pin current n Load regulation of 0 ...
Page 2
... Ordering Information Order Number LP3892ES-1.2 LP3892ESX-1.2 LP3892ET-1.2 LP3892ES-1.5 LP3892ESX-1.5 LP3892ET-1.5 LP3892ES-1.8 LP3892ESX-1.8 LP3892ET-1.8 Block Diagram www.national.com Package Type Package Drawing TO263-5 TS5B TO263-5 TS5B TO220-5 T05D TO263-5 TS5B TO263-5 TS5B TO220-5 T05D TO263-5 TS5B TO263-5 TS5B TO220-5 T05D 2 Supplied As Rail Tape and Reel ...
Page 3
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Storage Temperature Range Lead Temp. (Soldering, 5 seconds) ESD Rating Human Body Model (Note 3) Machine Model (Note 10) Power Dissipation (Note 2) V Supply Voltage (Survival) ...
Page 4
Electrical Characteristics over the full operating temperature range. Unless otherwise specified 10µ (Continued) OUT S/D BIAS Symbol Parameter AC Parameters PSRR (V ) Ripple Rejection for Voltage PSRR Ripple Rejection ...
Page 5
Typical Performance Characteristics 10 µF, S/D pin is tied 2.2V, V BIAS VSD GND DC Load Regulation Line Regulation vs V Unless otherwise specified 1.8V. OUT 20069605 20069607 BIAS 20069609 ...
Page 6
Typical Performance Characteristics µF, S/D pin is tied 2.2V, V BIAS VSD GND V Startup Waveform OUT Line Regulation vs V www.national.com Unless otherwise specified 1.8V. (Continued) OUT 20069612 20069615 ...
Page 7
Typical Performance Characteristics µF, S/D pin is tied 2.2V, V BIAS IN V PSRR IN V PSRR BIAS Unless otherwise specified 1.8V. (Continued) OUT 20069620 20069622 7 = 25˚ µF, ...
Page 8
Application Hints V RESTRICTIONS FOR PROPER START-UP BIAS To prevent misoperation, ensure that V before start-up is initiated. This scenario can occur in sys- tems with a backup battery using reverse-biased "blocking" diodes which may allow enough leakage current to ...
Page 9
Application Hints (Continued) HEATSINKING TO-220 PACKAGE The thermal resistance of a TO220 package can be reduced by attaching heat sink or a copper plane board copper plane used, the ...
Page 10
Application Hints (Continued) As shown in the graph below, increasing the copper area beyond 1 square inch produces very little improvement. The minimum value for θ for the TO-263 package mounted PCB is 32˚C/W. Figure 2 shows ...
Page 11
Physical Dimensions inches (millimeters) unless otherwise noted TO220 5-lead, Molded, Stagger Bend Package (TO220-5) NS Package Number T05D 11 www.national.com ...
Page 12
... NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant ...