BCW69LT1 Motorola Inc, BCW69LT1 Datasheet
BCW69LT1
Related parts for BCW69LT1
BCW69LT1 Summary of contents
Page 1
... General Purpose Transistors PNP Silicon MAXIMUM RATINGS Rating Collector–Emitter Voltage Emitter–Base Voltage Collector Current — Continuous DEVICE MARKING BCW69LT1 = H1; BCW70LT1 = H2 THERMAL CHARACTERISTICS Characteristic Total Device Dissipation FR-5 Board ( Derate above 25 C Thermal Resistance, Junction to Ambient Total Device Dissipation ...
Page 2
... BCW69LT1 BCW70LT1 ELECTRICAL CHARACTERISTICS ( unless otherwise noted) (Continued) Characteristic ON CHARACTERISTICS DC Current Gain ( –2.0 mAdc –5.0 Vdc) Collector–Emitter Saturation Voltage ( –10 mAdc –0.5 mAdc) Base–Emitter On Voltage ( –2.0 mAdc –5.0 Vdc) SMALL–SIGNAL CHARACTERISTICS Output Capacitance ( – ...
Page 3
... Noise Current of the Transistor referred to the input. (Figure 4) 1 Boltzman’s Constant (1. – Temperature of the Source Resistance ( K) 2 Source Resistance (Ohms) 3.0 dB 5.0 dB 500 700 1.0 k BCW69LT1 BCW70LT1 BANDWIDTH = 1 1.0 mA 300 A 100 100 200 500 1 ...
Page 4
... BCW69LT1 BCW70LT1 1 0.6 0.4 0.2 0 0.002 0.005 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2 BASE CURRENT (mA) Figure 6. Collector Saturation Region 1 1.2 1.0 0.8 V BE(sat 0.6 V BE(on 1.0 V 0.4 0.2 V CE(sat 0.1 0.2 0.5 1.0 2.0 5 COLLECTOR CURRENT (mA) Figure 8. “On” Voltages 4 TYPICAL STATIC CHARACTERISTICS 100 PULSE WIDTH = 300 s DUTY CYCLE 2 ...
Page 5
... FIGURE 16 P (pk 2.0 5 100 200 t, TIME (ms) Figure 14. Thermal Response BCW69LT1 BCW70LT1 – 3 – 3.0 – 5.0 – 7.0 –10 – 20 – 30 – 50 – 70 –100 COLLECTOR CURRENT (mA) Figure 11. Turn–Off Time ...
Page 6
... BCW69LT1 BCW70LT1 CEO CEX @ V BE(off –1 10 –2 – 4 – 100 + 120 + 140 + 160 JUNCTION TEMPERATURE ( C) Figure 15. Typical Collector Leakage Current 6 DESIGN NOTE: USE OF THERMAL RESPONSE DATA A train of periodical power pulses can be represented by the model as shown in Figure 16 ...
Page 7
... Gradual cooling should be used as the use of forced cooling will increase the temperature gradient and result in latent failure due to mechanical stress. Mechanical stress or shock should not be applied during cooling. * Soldering a device without preheating can cause excessive thermal shock and stress which can result in damage to the device. BCW69LT1 BCW70LT1 7 ...
Page 8
... BCW69LT1 BCW70LT1 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “ ...