AD9520-3 Analog Devices, Inc., AD9520-3 Datasheet - Page 40
AD9520-3
Manufacturer Part Number
AD9520-3
Description
12 Lvpecl/24 Cmos Output Clock Generator With Integrated 2 Ghz Vco
Manufacturer
Analog Devices, Inc.
Datasheet
1.AD9520-3.pdf
(84 pages)
- Current page: 40 of 84
- Download datasheet (2Mb)
AD9520-3
The holdover function senses the logic level of the LD pin as a
condition to enter holdover. The signal at LD can be from the
DLD, ALD, or current source LD mode. It is possible to disable
the LD comparator (0x01D[3]), which causes the holdover
function to always sense LD as being high. If DLD is used, it is
possible for the DLD signal to chatter while the PLL is reacquiring
lock. The holdover function may retrigger, thereby preventing
the holdover mode from terminating. Use of the current source
lock detect mode is recommended to avoid this situation (see the
Current Source Digital Lock Detect (CSDLD) section).
HIGH IMPEDANCE
HIGH IMPEDANCE
WHEN DLD WENT
LD PIN == HIGH
CHARGE PUMP
CHARGE PUMP
EDGE AT PFD?
PLL ENABLED
DLD == HIGH
DLD == LOW
REFERENCE
RELEASE
LOW?
WAS
YES
YES
YES
YES
YES
Figure 46. Flowchart of Automatic/Internal Holdover Mode
NO
NO
NO
NO
YES
Rev. 0 | Page 40 of 84
LOOP OUT OF LOCK. DIGITAL LOCK
DETECT SIGNAL GOES LOW WHEN THE
LOOP LEAVES LOCK AS DETERMINED
BY THE PHASE DIFFERENCE AT THE
INPUT OF THE PFD.
ANALOG LOCK DETECT PIN INDICATES
LOCK WAS PREVIOUSLY ACHIEVED.
(0x01D[3] = 1; USE LD PIN VOLTAGE
WITH HOLDOVER.
0x01D[3] = 0; IGNORE LD PIN VOLTAGE,
TREAT LD PIN AS ALWAYS HIGH.)
CHARGE PUMP IS MADE
HIGH IMPEDANCE.
PLL COUNTERS CONTINUE
OPERATING NORMALLY.
CHARGE PUMP REMAINS HIGH
IMPEDANCE UNTIL THE REFERENCE
HAS RETURNED.
TAKE CHARGE PUMP OUT OF
HIGH IMPEDANCE. PLL CAN
NOW RESETTLE.
WAIT FOR DLD TO GO HIGH. THIS TAKES
5 TO 255 CYCLES (PROGRAMMING OF THE DLD
DELAY COUNTER) WITH THE REFERENCE AND
FEEDBACK CLOCKS INSIDE THE LOCK WINDOW AT
THE PFD. THIS ENSURES THAT THE HOLDOVER
FUNCTION WAITS FOR THE PLL TO SETTLE AND LOCK
BEFORE THE HOLDOVER FUNCTION CAN BE
RETRIGGERED.
When in holdover mode, the charge pump stays in a high
impedance state as long as there is no reference clock present.
As in the external holdover mode, the B counter (in the N divider)
is reset synchronously with the charge pump leaving the high
impedance state on the reference path PFD event. This helps
align the edges out of the R and N dividers for faster settling of
the PLL and reduces frequency errors during settling. Because
the prescaler is not reset, this feature works best when the B and
R numbers are close because this results in a smaller phase
difference for the loop to settle out.
Related parts for AD9520-3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
12 Lvpecl/24 Cmos Output Clock Generator With Integrated 2.8 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12 Lvpecl/24 Cmos Output Clock Generator With Integrated 2.5 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12 Lvpecl/24 Cmos Output Clock Generator With Integrated 2.2 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12 Lvpecl/24 Cmos Output Clock Generator With Integrated 1.6 Ghz Vco
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
12 Lvpecl/24 Cmos Output Clock Generator
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Ultrasonic Bubble Air-in-line Sensors
Manufacturer:
Sensortechnics GmbH
Datasheet:
Part Number:
Description:
Analog Divider
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Analog Front End For Adsl
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Lc2mos Complete, 12-bit Analog I/o System
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Cmos 4/8 Channel Analog Multiplexers
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Low Cost, Low Power Cmos General Purpose Analog Front End
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
2.5 V To 5.0 V Micropower, Precision Series Mode Voltage References
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Stereo, Single-supply 18-bit Integrated Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Multichannel 24-bit, 192 Khz, Dac
Manufacturer:
Analog Devices, Inc.
Datasheet:
Part Number:
Description:
Ac?97 Soundmax Codec
Manufacturer:
Analog Devices, Inc.
Datasheet: