IRS2541 International Rectifier, IRS2541 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/338/international_rectifier_sml.jpg)
IRS2541
Manufacturer Part Number
IRS2541
Description
(IRS2540 / IRS2541) LED Buck Regulator Control IC
Manufacturer
International Rectifier
Datasheet
1.IRS2541.pdf
(14 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IRS25411PBF
Manufacturer:
IR
Quantity:
20 000
Company:
Part Number:
IRS25411STRPBF
Manufacturer:
IR
Quantity:
3 000
www.DataSheet4U.com
DataSheet
www.irf.com
HO
LO
4
Watchdog Timer
During an open circuit condition, without the
watchdog timer, the HO output would remain high at
all times and the charge stored in the bootstrap
capacitor C
floating power supply for the high-side driver, which
would then be unable to fully switch on the upper
MOSFET causing high losses.
sufficient charge on the bootstrap capacitor, a
watchdog timer has been implemented.
condition where V
output will be forced low after 20 µs and the LO
output forced high. This toggling of the outputs will
last for approximately 1 µs to maintain and replenish
sufficient charge on C
Bootstrap Capacitor and Diode
The bootstrap capacitor value needs to be chosen
so that it maintains sufficient charge for at least the
approximately 20 µs interval until the watchdog timer
allows the capacitor to recharge. If the capacitor
value is too small, the charge will dissipate in less
than 20 µs.
approximately 100 nF.
The bootstrap diode should be a fast recovery or
ultrafast recovery component to maintain good
efficiency. Since the cathode of the bootstrap diode
will be switching between zero and to the high
voltage bus, the reverse recovery time of this diode
is of critical importance. For additional information
concerning the bootstrap components, refer to the
U
.com
Fig.4 Illustration of Watchdog Timer
BOOT
The typical bootstrap capacitor is
IFB
would gradually discharge the
BOOT
remains below V
.
To maintain
IFBTH
, the HO
In the
Design Tip (DT 98-2), “Bootstrap Component
Selection For Control ICs” at
Design Support
Disable (ENN) Pin
The disable pin can be used for dimming and open-
circuit protection. When the ENN pin is held low, the
chip remains in a fully functional state with no
alterations to the operating environment. To disable
the control feedback and regulation, a voltage
greater than V
applied to the ENN pin. With the chip in a disabled
state, HO output will remain low, whereas the LO
output will remain high to prevent V
addition to maintaining charge on the bootstrap
capacitor.
IRS254(0,1) has been set to 2.5 V to enhance
immunity to any externally generated noise, or
application ground noise. This 2.5 V threshold also
makes it ideal to receive a drive signal from a local
microcontroller.
Dimming Mode
To achieve dimming, a signal with constant
frequency and set duty cycle can be fed into the
ENN pin.
between the average load current and duty cycle. If
the ratio is 50%, 50% of the maximum set light
output will be realized. Likewise if the ratio is 30%,
70% of the maximum set light output will be realized.
A sufficiently high frequency of the dimming signal
must be chosen to avoid flashing or “strobe light”
effect. A signal on the order of a few kHz should be
sufficient.
The minimum amount of dimming achievable (light
output approaches 0%) will be determined by the
“on” time of the HO output, when in a fully functional
regulating state. To maintain reliable dimming, it is
recommended to keep the “off” time of the enable
signal at least 10 times that of the HO “on” time. For
example, if the application is running at 75 kHz with
an input voltage of 100 V and an output voltage of
20 V, the HO “on” time will be 3.3 µs (one-fourth of
the period – see calculations below) according to
standard buck topology theory.
minimum “off” time of the enable signal to 33 µs.
Duty
HO
on
Cycle
time
=
There is a direct linear relationship
20
ENTH
=
The
V
%
V
out
in
IRS254(0,1)(S)PbF
*
(approximately 2.5 V) needs to be
1
threshold
∗
75
100
kHz
=
100
=
20
3
V
for
www.irf.com
V
3 .
This will set the
µ
S
*
s
from floating, in
100
disabling
Page 8
=
20
%
under
the