LT1462 Linear Technology, LT1462 Datasheet
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LT1462
Available stocks
Related parts for LT1462
LT1462 Summary of contents
Page 1
... This unique combination of performance makes the LT1462/LT1463 ideal over a wide range of input and output impedances. In the design and testing of the LT1462/LT1463, particular emphasis has been placed on optimizing performance in the low cost SO-8 (dual) and 14-lead SO package (quad) for 15V and 5V supplies ...
Page 2
... LT1463CS 3 12 +IN D – + – OUT C S PACKAGE 14-LEAD PLASTIC SO = 150 C, = 110 150 C, = 150 unless otherwise noted. A LT1462AC LT1462C/LT1463C TYP MAX MIN TYP MAX 0.4 0.8 0.4 0.8 0.6 2.0 0.6 2.0 0.3 1.2 0.5 2.0 0.5 15 0.5 2 ...
Page 3
... MIN TYP MAX 13.7 13.5 13.7 12.4 11.0 12.4 3.7 3.5 3 0.13 0.08 0.13 175 125 175 132 132 0.5 1.3 0.5 1.3 0.8 3.0 0.8 3.0 0.4 3.0 0.5 4.0 0 LT1462AC LT1462C/LT1463C TYP MAX MIN TYP MAX 0.5 1.4 0.5 1.4 0.9 2.8 0.9 2 450 60 150 150 750 600 90 600 140 45 140 13.6 13.4 13.6 12.1 10.5 12.1 3.6 3.4 3.6 0.128 0.075 0.128 ...
Page 4
... Note 1: Typical parameters are defined as 60% yield of parameter distributions of individual amplifiers, i.e., out of 100 LT1463s (or 100 LT1462s) typically 240 op amps (or 120) will be better than the indicated specification. Note 2: The LT1462 and LT1463 are designed, characterized and expected to meet these extended temperature limits, but are not tested at – and 85 C ...
Page 5
... Common Mode Range vs Temperature –11 –12 –13 – –15 15 –75 –50 – TEMPERATURE ( C) LT1462 • TPC03 0.1Hz to 10Hz Noise TIME (SEC) Channel Separation vs Frequency 160 V = 15V 10k 140 L 120 100 80 60 ...
Page 6
... Power Supply Rejection Ratio vs Frequency 120 15V 100 POSITIVE SUPPLY 80 NEGATIVE SUPPLY 100k 1M 10 100 1k 10k FREQUENCY (Hz) LT1462 • TPC11 Closed-Loop Output Impedance 10k V = 15V 1000pF L 100 10 1 0.1 100 125 10 100 1k 10k FREQUENCY (Hz) ...
Page 7
... JFET input op amp in the unity- gain follower mode (Figure 1b) and the response of the LT1462/LT1463 (Figure 1c). The phase reversal of Figure 1b can cause lock-up in servo systems. The LT1462/LT1463 does not phase-reverse when the common mode input is anywhere within the supplies. LT1462 • F01a (1b) Typical JFET Input Op Amp with 5V Supplies LT1462 • ...
Page 8
... REF 1000pF – 154k C3 10nF 13 – 14 1/4 LT1463 V OUT 12 + LT1462 • TA05 R2 10k GAIN TRIM 75k – 1/2 LT1462 OUTPUT – (R2)( )(f ) OUT S REF IN * TRW#MTR-5/120ppm LT1462 • TA04 ...
Page 9
... R10 Q16 C1 Q28 V EE R16 Q11 Q13 Q10 R10 LT1462/LT1463 V CC R20 Q17 R17 Q22 Q20 R22 R1O Q29 Q21 Q23 Q25 Q24 Q27 Q26 1462 Q18 R18 OUT R19 Q19 9 ...
Page 10
... LT1462/LT1463 PACKAGE DESCRIPTION 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.025 0.325 –0.015 +0.635 8.255 –0.381 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 0.010 – 0.020 45 (0.254 – ...
Page 11
... DWG # 05-08-1610) (8.560 – 8.738 0.228 – 0.244 (5.791 – 6.197 0.053 – 0.069 (1.346 – 1.752) 0 – 8 TYP 0.014 – 0.019 (0.355 – 0.483) LT1462/LT1463 0.770* (19.558) MAX 0.065 (1.651) TYP 0.018 0.003 (0 ...
Page 12
... Drive 10nF Capacitive Loads, 1MHz GBW LT1009 V = – 2.5V REF 0kHz TO 3kHz OUT OUT (R )( REF IN IN LT1462 • TA03 , 6.3MHz GBW B , 5.3MHz GBW, 1.5pF Input Capacitance Drift OS(MAX) 14623fa LT/GP 0197 5K REV A • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1996 ...