LT1507 Linear Technology, LT1507 Datasheet - Page 19

no-image

LT1507

Manufacturer Part Number
LT1507
Description
500kHz Monolithic Buck Mode Switching Regulator
Manufacturer
Linear Technology
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT15073
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LT15073CS8
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LT1507CN8
Manufacturer:
TI
Quantity:
100
Part Number:
LT1507CN8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1507CS8
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LT1507CS8
Quantity:
10
Part Number:
LT1507CS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1507CS8#TR
Manufacturer:
SEOUL
Quantity:
3 223
Part Number:
LT1507CS8-3.3
Manufacturer:
LT
Quantity:
10 000
Part Number:
LT1507CS8-3.3#TR
Quantity:
172
Company:
Part Number:
LT1507CS8-3.3#TRPBF
Quantity:
1 905
Part Number:
LT1507IN8
Manufacturer:
LT
Quantity:
21
PACKAGE
APPLICATIONS
components. In many cases only C
will improve phase margin, but this may necessitate the need
for C
In Figure 10, full loop phase/gain characteristics are shown
with a compensation capacitor (C
error amplifier a pole at 240Hz, with phase rolling off to 90
and staying there. The overall loop has a gain of 77dB at low
frequency rolling off to unity gain at 20kHz. Phase shows a
2-pole characteristic until the ESR of the output capacitor
brings it back above 10kHz. Phase margin is about 60 at
unity-gain.
Analog experts will note that around 1kHz, phase dips to
within 20 of the zero phase margin line. This is typical of
switching regulators because of the 2-pole rolloff generated
by the output capacitor and the compensation network. This
region of low phase is not a problem as long as it does not
occur near unity-gain. In practice, the variability of output
capacitor ESR tends to dominate all other effects with respect
to loop response. Variations in ESR will cause unity-gain to
F
to limit switching frequency ripple at the V
*THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS.
MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm)
(7.620 – 8.255)
(0.229 – 0.381)
0.009 – 0.015
0.300 – 0.325
0.325
8.255
DESCRIPTION
+0.635
–0.381
+0.025
–0.015
U
INFORMATION
U
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen-
tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
(1.651)
0.065
TYP
C
) of 0.0033 F, giving the
(2.540 0.254)
(0.127)
0.100 0.010
C
0.005
MIN
W
is needed. Adding R
U
(1.143 – 1.651)
0.045 – 0.065
Dimensions in inches (millimeters) unless otherwise noted.
8-Lead PDIP (Narrow 0.300)
U
C
pin.
(LTC DWG # 05-08-1510)
N8 Package
C
(0.457 0.076)
0.018 0.003
move around, but at the same time phase moves with it so
that adequate phase margin is maintained over a very wide
range of ESR ( 5:1)
Undervoltage Lockout
See Application Information in LT1376 data sheet.
(3.302 0.127)
0.130 0.005
(3.175)
0.125
MIN
–20
(0.380)
80
60
40
20
Figure 10. Overall Loop Phase and Gain
0.015
MIN
0
0.01
(6.477 0.381)
0.255 0.015*
0.1
GAIN
FREQUENCY (kHz)
C
OUT
1
V
OUT
= 100 F, 10V, AVX TPS
= 5V, I
C
10
C
8
1
= 3.3nF, R
OUT
PHASE
V
7
2
(10.160)
= 500mA
L = 10 H
100
IN
0.400*
MAX
= 10V
LT1511 • F10
C
= 0
6
3
100
200
150
100
50
0
–50
LT1507
5
4
N8 0695
19

Related parts for LT1507