LT1636 Linear Technology, LT1636 Datasheet
LT1636
Available stocks
Related parts for LT1636
LT1636 Summary of contents
Page 1
... There is no phase reversal of the output for inputs 5V below V 44V above V The LT1636 op amp is available in the 8-pin MSOP, PDIP and SO packages. , LTC and LT are registered trademarks of Linear Technology Corporation. Over-The-Top is a trademark of Linear Technology Corporation. ...
Page 2
... 0.1Hz to 10Hz f = 1kHz f = 1kHz ORDER PART TOP VIEW NUMBER 8 NULL LT1636CN8 + 7 V LT1636CS8 6 OUT LT1636IN8 5 SHDN LT1636IS8 N8 PACKAGE S8 PART MARKING S8 PACKAGE 1636 = 130 C/ W (N8 190 C/ W (S8) JA 1636I = 25 C unless otherwise noted. (Note 3) A MIN TYP MAX 50 225 ...
Page 3
... PIN5 5V 10k PIN5 1kHz – – – LT1636 MIN TYP MAX UNITS 110 200 1300 V/mV ...
Page 4
... LT1636 15V ELECTRICAL CHARACTERISTICS V = 15V 0V 0V, Pin 5 = open OUT SYMBOL PARAMETER V Input Offset Voltage OS Input Offset Voltage Drift (Note 8) I Input Offset Current OS I Input Bias Current B Input Noise Voltage e Input Noise Voltage Density n i Input Noise Current Density ...
Page 5
... Note 2: A heat sink may be required to keep the junction temperature below absolute maximum. Note 3: The LT1636C is guaranteed to meet specified performance from and is designed, characterized and expected to meet these extended temperature limits, but is not tested at –40 C and 85 C. The LT1636I is guaranteed to meet the extended temperature limits ...
Page 6
... LT1636 W U TYPICAL PERFOR A CE CHARACTERISTICS 0.1Hz to 10Hz Noise Voltage TIME (SEC) 1636 G07 Open-Loop Gain and Phase Shift vs Frequency 2. PHASE 30 20 GAIN 10 0 –10 –20 –30 1k 10k 100k 1M FREQUENCY (Hz) 1636 G10 ...
Page 7
... FREQUENCY (Hz) 1636 G20 Total Harmonic Distortion + Noise vs Output Voltage R = 10k HALF SUPPLY 1kHz A = – 1. 1. – 3V 3V OUTPUT VOLTAGE (V ) P-P 1636 G23 LT1636 = 1 10k 100k 1635 G18 1k 10k 1636 G21 7 ...
Page 8
... When monitoring voltages within 100mV the PNP should be taken to keep the output from clipping. The output of the LT1636 can be pulled up to 27V beyond + V with less than 1nA of leakage current, provided that V is less than 0.5V. ...
Page 9
... U returned to ground. The typical performance photo of Open-Loop Gain for various loads shows the details. Shutdown The LT1636 can be shut down two ways: using the shutdown pin or bringing V is brought to within 0. output leakage current drop to less than 1nA. When the shutdown pin is brought 1.2V above V ...
Page 10
... OUT 1636 TA05 Optional Output Compensation for Capacitive Loads Greater Than 200pF + V IN LT1636 C – L 0.22 F 150 1636 TA09 Q13 Q10 Q14 Q15 1k Q11 Q12 Q16 D4 D5 NULL 1 MUX Amplifier Waveforms ...
Page 11
... Plastic Small Outline (Narrow 0.150) (LTC DWG # 05-08-1610) 0.053 – 0.069 0.004 – 0.010 (1.346 – 1.752) (0.101 – 0.254) 0.050 0.014 – 0.019 (0.355 – 0.483) (1.270) TYP LT1636 0.118 0.004* (3.00 0.102 0.118 0.004** 0.192 0.004 (3.00 0.102) (4.88 0.10) MSOP (MS8) 1197 4 ...
Page 12
... V V 120 44V – LT1636 V = 1.25V OUT I 10mA OUT + 1N5711 1M LT1634-1.25 1636 TA04 Over-The-Top Current Sense R1 200 LT1636 V – OUT (0V TO 4.3V) I LOAD OUT I = LOAD (R )(R2/R1) 1636 TA08 S , Gain Bandwidth = 120kHz OS(MAX) , Gain Bandwidth = 200kHz OS(MAX) , 1.5 A Supply Current Max ...