LT6201 Linear Technology, LT6201 Datasheet - Page 10

• Manufacturer Part Number: LT6201
• Description: (LT6200 / LT6201) Op Amp Family
• Manufacturer: Linear Technology

LT6200/LT6200-5
LT6200-10/LT6201
Note 5: The LT6200C/LT6201C are guaranteed to meet specified
performance from 0 C to 70 C. The LT6200C/LT6201C are designed,
characterized and expected to meet specified performance from – 40 C to
85 C, but are not tested or QA sampled at these temperatures. The
LT6200I is guaranteed to meet specified performance from –40 C to 85 C.
Note 6: Minimum supply voltage is guaranteed by power supply rejection
ratio test.
Note 7: Output voltage swings are measured between the output and
power supply rails.
Note 8: This parameter is not 100% tested.
Note 9: Full-power bandwidth is calculated from the slew rate:
FPBW = SR/2 V
ELECTRICAL CHARACTERISTICS
10
TYPICAL PERFOR A CE CHARACTERISTICS
80
70
60
50
40
30
20
10
30
25
10
20
15
–1000
0
5
0
0
V
Supply Current vs Supply Voltage
V
SO-8
OS
S
= 5V, 0V
Distribution, V
2
–600
INPUT OFFSET VOLTAGE ( V)
TOTAL SUPPLY VOLTAGE (V)
P
4
–200
6
T
T
T
A
A
A
= 125 C
= –55 C
= 25 C
CM
8
200
= V
10
+
W
600
/2
12
6200 G04
6200 G01
U
1000
14
–0.5
–1.0
–1.5
3.0
2.5
2.0
1.5
1.0
0.5
80
70
60
50
40
30
20
10
0
–1600–1200
0
0
V
Offset Voltage
vs Input Common Mode Voltage
V
SO-8
OS
S
INPUT COMMON MODE VOLTAGE (V)
= 5V, 0V
Distribution, V
INPUT OFFSET VOLTAGE ( V)
1
–800 –400
T
T
2
T
A
A
A
= 125 C
= –55 C
= 25 C
Note 10: Thermal resistance varies depending upon the amount of PC
board metal attached to the V
certain amount of 2oz copper metal trace connecting to the V
described in the thermal resistance tables in the Application Information
section.
Note 11: Matching parameters on the LT6201 are the difference between
the two amplifiers. CMRR and PSRR match are defined as follows: CMRR
and PSRR are measured in V/V on the identical amplifiers. The difference
is calculated in V/V. The result is converted to dB.
Note 12: There are reverse biased ESD diodes on all inputs and outputs as
shown in Figure 1. If these pins are forced beyond either supply, unlimited
current will flow through these diodes. If the current is transient in nature
and limited to less than 30mA, no damage to the device will occur.
0
CM
400 800 1200
3
= V
V
TYPICAL PART
S
= 5V, 0V
+
4
6200 G05
6200 G02
1600
5
–
–20
–40
–10
–30
80
70
60
50
40
30
20
10
20
10
pin of the device.
–1600–1200
0
0
–1
V
Input Bias Current
vs Common Mode Voltage
V
V
SO-8
OS
S
S
= 5V, 0V
= 5V, 0V
Distribution, V
0
T
T
INPUT OFFSET VOLTAGE ( V)
COMMON MODE VOLTAGE (V)
A
–800 –400
A
= 125 C
= 25 C
1
T
A
= –55 C
JA
2
is specified for a
0
CM
3
400 800 1200
= V
–
4
–
pin as
5
6200 G03
6200 G06
62001fa
1600
6