LTC3727-1 Linear Technology, LTC3727-1 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC3727-1
Manufacturer Part Number
LTC3727-1
Description
2-Phase Synchronous Step-Down Switching Regulators
Manufacturer
Linear Technology
Datasheet
1.LTC3727-1.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3727-1EG
Manufacturer:
LT
Quantity:
13
OPERATIO
LTC3727/LTC3727-1
The top MOSFET drivers are biased from floating boot-
strap capacitor C
each off cycle through an external diode when the top
MOSFET turns off. As V
V
the top MOSFET continuously. The dropout detector de-
tects this and forces the top MOSFET off for about 400ns
every tenth cycle to allow C
The main control loop is shut down by pulling the RUN/SS
pin low. Releasing RUN/SS allows an internal 1.2 A
current source to charge soft-start capacitor C
C
I
value. As C
gradually released allowing normal, full-current opera-
tion. When both RUN/SS1 and RUN/SS2 are low, all
LTC3727/LTC3727-1 controller functions are shut down,
including the 7.5V and 3.3V regulators.
Low Current Operation
The FCB pin is a multifunction pin providing two func-
tions: 1) to provide regulation for a secondary winding by
temporarily forcing continuous PWM operation on
both controllers; and 2) select between two modes of low
current operation. When the FCB pin voltage is below
0.8V, the controller forces continuous PWM current
mode operation. In this mode, the top and bottom
MOSFETs are alternately turned on to maintain the output
voltage independent of direction of inductor current.
When the FCB pin is below V
0.8V, the controller enters Burst Mode operation. Burst
Mode operation sets a minimum output current level
before inhibiting the top switch and turns off the synchro-
nous MOSFET(s) when the inductor current goes nega-
tive. This combination of requirements will, at low cur-
rents, force the I
temporarily inhibit turn-on of both output MOSFETs until
the output voltage drops. There is 60mV of hysteresis in
the burst comparator B tied to the I
produces output signals to the MOSFETs that turn them
on for several cycles, followed by a variable “sleep”
interval depending upon the load current. The resultant
output voltage ripple is held to a very small value by
10
TH
OUT
SS
voltage clamped at approximately 30% of its maximum
reaches 1.5V, the main control loop is enabled with the
, the loop may enter dropout and attempt to turn on
SS
continues to charge, the I
TH
B
U
, which normally is recharged during
pin below a voltage threshold that will
(Refer to Functional Diagram)
IN
decreases to a voltage close to
B
INTVCC
to recharge.
TH
– 2V but greater than
pin. This hysteresis
TH
pin voltage is
SS
. When
having the hysteretic comparator after the error amplifier
gain block.
Frequency Synchronization
The phase-locked loop allows the internal oscillator to be
synchronized to an external source via the PLLIN pin. The
output of the phase detector at the PLLFLTR pin is also the
DC frequency control input of the oscillator that operates
over a 250kHz to 550kHz range corresponding to a DC
voltage input from 0V to 2.4V. When locked, the PLL aligns
the turn on of the top MOSFET to the rising edge of the
synchronizing signal. When PLLIN is left open, the PLLFLTR
pin goes low, forcing the oscillator to minimum frequency.
Continuous Current (PWM) Operation
Tying the FCB pin to ground will force continuous current
operation. This is the least efficient operating mode, but
may be desirable in certain applications. The output can
source or sink current in this mode. When sinking current
while in forced continuous operation, current will be
forced back into the main power supply potentially boost-
ing the input supply to dangerous voltage levels—
BEWARE!
INTV
Power for the top and bottom MOSFET drivers and most
other internal circuitry is derived from the INTV
When the EXTV
dropout linear regulator supplies INTV
is taken above 7.3V, the 7.5V regulator is turned off and an
internal switch is turned on connecting EXTV
This allows the INTV
efficiency external source such as the output of the regu-
lator itself or a secondary winding, as described in the
Applications Information section.
Output Overvoltage Protection
An overvoltage comparator, OV, guards against transient
overshoots (>7.5%) as well as other more serious condi-
tions that may overvoltage the output. In this case, the top
MOSFET is turned off and the bottom MOSFET is turned on
until the overvoltage condition is cleared.
CC
/EXTV
CC
CC
Power
pin is left open, an internal 7.5V low
CC
power to be derived from a high
www.DataSheet4U.com
CC
power. If EXTV
CC
to INTV
CC
pin.
3727f
CC
CC
.