LTC3728 Linear Technology, LTC3728 Datasheet - Page 28

no-image

LTC3728

Manufacturer Part Number
LTC3728
Description
2-Phase Synchronous Step-Down Switching Regulator
Manufacturer
Linear Technology
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LTC3728EG
Manufacturer:
MAXIM
Quantity:
158 341
Part Number:
LTC3728EG
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC3728EG#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3728EG#TRPBF
Manufacturer:
LINEAR
Quantity:
63
Part Number:
LTC3728EG#TRPBF
Manufacturer:
LINEART
Quantity:
20 000
Company:
Part Number:
LTC3728EG#TRPBF
Quantity:
575
Part Number:
LTC3728EG-1
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3728EGTRPBF
Manufacturer:
LINEAR
Quantity:
1 350
Part Number:
LTC3728ES
Manufacturer:
LT
Quantity:
1 500
Part Number:
LTC3728EUH
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC3728EUH
Manufacturer:
LT
Quantity:
2 420
Part Number:
LTC3728EUH
Manufacturer:
LT
Quantity:
20 000
Company:
Part Number:
LTC3728EUH#TRPBF
Quantity:
2 500
LTC3728
APPLICATIO S I FOR ATIO
7. Use a modified “star ground” technique: a low imped-
ance, large copper area central grounding point on the
same side of the PC board as the input and output
capacitors with tie-ins for the bottom of the INTV
decoupling capacitor, the bottom of the voltage feedback
resistive divider and the SGND pin of the IC.
PC Board Layout Debugging
Start with one controller on at a time. It is helpful to use a
DC-50MHz current probe to monitor the current in the
inductor while testing the circuit. Monitor the output
switching node (SW pin) to synchronize the oscilloscope
to the internal oscillator and probe the actual output
voltage as well. Check for proper performance over the
operating voltage and current range expected in the appli-
cation. The frequency of operation should be maintained
over the input voltage range down to dropout and until the
output load drops below the low current operation thresh-
old—typically 10% to 20% of the maximum designed
current level in Burst Mode operation.
The duty cycle percentage should be maintained from
cycle to cycle in a well-designed, low noise PCB imple-
mentation. Variation in the duty cycle at a subharmonic
rate can suggest noise pickup at the current or voltage
sensing inputs or inadequate loop compensation. Over-
compensation of the loop can be used to tame a poor PC
layout if regulator bandwidth optimization is not required.
Only after each controller is checked for their individual
performance should both controllers be turned on at the
same time. A particularly difficult region of operation is
when one controller channel is nearing its current com-
parator trip point when the other channel is turning on its
top MOSFET. This occurs around 50% duty cycle on either
channel due to the phasing of the internal clocks and may
cause minor duty cycle jitter.
28
U
U
W
U
CC
Short-circuit testing can be performed to verify proper
overcurrent latchoff, or 5µA can be provided to the RUN/
SS pin(s) by resistors from V
latchoff from occurring.
Reduce V
regulator in dropout. Check the operation of the under-
voltage lockout circuit by further lowering V
toring the outputs to verify operation.
Investigate whether any problems exist only at higher
output currents or only at higher input voltages. If prob-
lems coincide with high input voltages and low output
currents, look for capacitive coupling between the BOOST,
SW, TG, and possibly BG connections and the sensitive
voltage and current pins. The capacitor placed across the
current sensing pins needs to be placed immediately
adjacent to the pins of the IC. This capacitor helps to
minimize the effects of differential noise injection due to
high frequency capacitive coupling. If problems are en-
countered with high current output loading at lower input
voltages, look for inductive coupling between C
and the top MOSFET components to the sensitive current
and voltage sensing traces. In addition, investigate com-
mon ground path voltage pickup between these compo-
nents and the SGND pin of the IC.
An embarrassing problem, which can be missed in an
otherwise properly working switching regulator, results
when the current sensing leads are hooked up backwards.
The output voltage under this improper hookup will still be
maintained but the advantages of current mode control
will not be realized. Compensation of the voltage loop will
be much more sensitive to component selection. This
behavior can be investigated by temporarily shorting out
the current sensing resistor—don’t worry, the regulator
will still maintain control of the output voltage.
IN
from its nominal level to verify operation of the
IN
to prevent the short-circuit
www.DataSheet4U.com
IN
while moni-
IN
, Schottky
3728fb

Related parts for LTC3728