mic5319-2.9yml Micrel Semiconductor, mic5319-2.9yml Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/435/micrel_semiconductor_sml.jpg)
mic5319-2.9yml
Manufacturer Part Number
mic5319-2.9yml
Description
Mic5319 500ma ?cap Ultra-low Dropout, High Psrr Ldo Regulator
Manufacturer
Micrel Semiconductor
Datasheet
1.MIC5319-2.9YML.pdf
(11 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MIC5319-2.9YML
Manufacturer:
MICREL
Quantity:
13 000
Part Number:
MIC5319-2.9YML
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Applications Information
Enable/Shutdown
The MIC5319 features an active-high enable pin that allows
the regulator to be disabled. Forcing the enable pin low dis-
ables the regulator and sends it into a “zero” off-mode-current
state. In this state, current consumed by the regulator goes
nearly to zero. Forcing the enable pin high enables the output
voltage. The active-high enable pin uses CMOS technology
and the enable pin cannot be left floating, as this may cause
an indeterminate state on the output.
Input Capacitor
The MIC5319 is a high-performance, high bandwidth device.
Therefore, it requires a well-bypassed input supply for optimal
performance. A 1µF capacitor is required from the input- to-
ground to provide stability. Low-ESR ceramic capacitors
provide optimal performance at a minimum of space. Addi-
tional high frequency capacitors, such as small-valued NPO
dielectric-type capacitors, help filter out high-frequency noise
and are good design practice in any RF-based circuit.
Output Capacitor
The MIC5319 requires an output capacitor of 2.2µF or greater
to maintain stability. The design is optimized for use with
low-ESR ceramic chip capacitors. High ESR capacitors may
cause high frequency oscillation. The output capacitor can be
increased, but performance has been optimized for a 2.2µF
ceramic output capacitor and does not improve significantly
with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are recom-
mended because of their temperature performance. X7R-type
capacitors change capacitance by 15% over their operating
temperature range and are the most stable type of ceramic
capacitors. Z5U and Y5V dielectric capacitors change value
by as much as 50% and 60%, respectively, over their operat-
ing temperature ranges. To use a ceramic chip capacitor with
Y5V dielectric, the value must be much higher than an X7R
ceramic capacitor to ensure the same minimum capacitance
over the equivalent operating temperature range.
Bypass Capacitor
A capacitor can be placed from the bypass pin-to-ground
to reduce output voltage noise. The capacitor bypasses
the internal reference. A 0.1µF capacitor is recommended
for applications that require low-noise outputs. The bypass
capacitor can be increased, further reducing noise and im-
proving PSRR. Turn-on time increases slightly with respect
to bypass capacitance. A unique, quick-start circuit allows
the MIC5319 to drive a large capacitor on the bypass pin
without significantly slowing turn-on time. Refer to the “Typi-
cal Characteristics” section for performance with different
bypass capacitors.
March 2008
9
No-Load Stability
Unlike many other voltage regulators, the MIC5319 will re-
main stable and in regulation with no load. This is especially
important in CMOS RAM keep-alive applications.
Adjustable Regulator Application
Adjustable regulators use the ratio of two resistors to multiply
the reference voltage to produce the desired output voltage.
The MIC5319 can be adjusted from 1.25V to 5.5V by using
two external resistors (Figure 1). The resistors set the output
voltage based on the following equation:
Thermal Considerations
The MIC5319 is designed to provide 500mA of continuous
current in a very small MLF package. Maximum ambient
operating temperature can be calculated based on the output
current and the voltage drop across the part. Given an input
voltage of 3.3V, output voltage of 2.8V and output current =
500mA, the actual power dissipation of the regulator circuit
can be determined using the equation:
Because this device is CMOS and the ground current is
typically <100µA over the load range, the power dissipation
contributed by the ground current is < 1% and can be ignored
for this calculation.
To determine the maximum ambient operating temperature of
the package, use the junction-to-ambient thermal resistance
of the device and the following basic equation:
T
the die θ
J
(max) = 125°C, the maximum junction temperature of
P
P
P
P (
V
V
D
D
D
D
Figure 1. Adjustable Voltage Application
REF
OUT
JA
max) =
= (V
= (3.3V – 2.8V) × 500mA
= 0.25W
V
1µF
thermal resistance = 93°C/W.
IN
=
=
IN
1.25V
V
– V
REF
T (max) – T
J
OUT
1
+
θ
) I
MIC5319BML
VIN
BYP
JA
EN
R2
R1
OUT
GND
VOUT
ADJ
+ V
A
IN
× I
GND
R1
R2
V
2.2µF
OUT
M9999-032808