b32672z6104k289 EPCOS AG, b32672z6104k289 Datasheet

Page 1

... Film Capacitors Metallized Polypropylene Film Capacitors (MKP) Series/Type: B32671Z ... B32673Z Date: April 2009 © EPCOS AG 2009. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...

Page 2

Metallized polypropylene film capacitors (MKP) Power Factor Correction Typical applications PFC (Power Factor Correction) Not suitable for "across the line" applications Climatic Max. operating temperature: 125 C Climatic category (IEC 60068-1): 55/110/56 Construction Dielectric: metallized polypropylene (PP) Wound capacitor technology ...

Page 3

Overview of available types Lead spacing Type B32671Z B32672Z Page AC) 310 220 RMS V (V DC) 630 450 0.010 0.015 0.022 0.033 0.047 0.068 0.10 0.12 ...

Page 4

B32671Z Power Factor Correction Ordering codes and packing units (lead spacing 10 mm Max. dimensions RMS kHz 310 630 0.010 4.0 9.0 0.015 4.0 9.0 ...

Page 5

Ordering codes and packing units (lead spacing 15 mm Max. dimensions RMS kHz 220 450 0.10 5.0 10.5 0.15 5.0 10.5 0.22 6.0 11.0 0.33 ...

Page 6

B32673Z Power Factor Correction Ordering codes and packing units (lead spacing 22.5 mm Max. dimensions RMS kHz 220 450 0.22 6.0 15.0 0.22 7.5 14.0 ...

Page 7

Technical data Max. operating temperature T op,max Dissipation factor tan ( (upper limit values) Insulation resistance R ins or time constant = ins rel. humidity 65% (minimum as-delivered values) ...

Page 8

B32671Z ... B32673Z Power Factor Correction Pulse handling capability "dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal voltages, expressed "k " represents the maximum permissible pulse characteristic of the waveform applied to ...

Page 9

Permissible AC voltage V RMS For T >90 C, please refer to "General technical information", section 3.2.3. A Lead spacing 10 mm 630 V DC/310 V AC Please read Cautions and warnings and Important notes at the end of this ...

Page 10

B32672Z Power Factor Correction Permissible AC voltage V RMS For T >100 C, please refer to "General technical information", section 3.2.3. A Lead spacing 15 mm 450 V DC/220 V AC 630 V DC/310 V AC Please read Cautions and ...

Page 11

Permissible AC voltage V RMS For T >100 C, please refer to "General technical information", section 3.2.3. A Lead spacing 22.5 mm 450 V DC/220 V AC 630 V DC/310 V AC Please read Cautions and warnings and Important notes ...

Page 12

B32671Z ... B32673Z Power Factor Correction Mounting guidelines 1 Soldering 1.1 Solderability of leads The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1. Before a solderability test is carried out, terminals are subjected to accelerated ...

Page 13

Immersion depth Shield Evaluation criteria: Visual inspection C/C 0 tan Please read Cautions and warnings and Important notes at the end of this document. B32671Z ... B32673Z Power Factor Correction 2.0 +0/ 0.5 mm from capacitor body or seating plane ...

Page 14

B32671Z ... B32673Z Power Factor Correction 1.3 General notes on soldering Permissible heat exposure loads on film capacitors are primarily characterized by the upper cate- gory temperature T . Long exposure to temperatures above this type-related temperature limit max can ...

Page 15

Cleaning To determine whether the following solvents, often used to remove flux residues and other sub- stances, are suitable for the capacitors described, refer to the table below: Type Ethanol, isopropanol, n-propanol MKT Suitable (uncoated) MKT, MKP, MFP (coated/boxed) ...

Page 16

B32671Z ... B32673Z Power Factor Correction 3 Embedding of capacitors in finished assemblies In many applications, finished circuit assemblies are embedded in plastic resins. In this case, both chemical and thermal influences of the embedding ("potting") and curing processes must ...

Page 17

Cautions and warnings Do not exceed the upper category temperature (UCT). Do not apply any mechanical stress to the capacitor terminals. Avoid any compressive, tensile or flexural stress. Do not move the capacitor after it has been soldered to the ...

Page 18

B32671Z ... B32673Z Power Factor Correction Topic Safety information Soldering Do not exceed the specified time or temperature limits during soldering. Cleaning Use only suitable solvents for cleaning capacitors. 2 "Cleaning" Embedding of When embedding finished circuit assemblies in capacitors ...

Page 19

Symbols and terms Symbol English Heat transfer coefficient Temperature coefficient of capacitance C A Capacitor surface area Humidity coefficient of capacitance C C Capacitance C Rated capacitance R C Absolute capacitance change C/C Relative capacitance change (relative deviation of actual ...

Page 20

B32671Z ... B32673Z Power Factor Correction Symbol English I (Sinusoidal) alternating current, RMS root-mean-square value i Capacitance drift z k Pulse characteristic 0 L Series inductance S Failure rate Constant failure rate during useful 0 service life Failure rate, determined ...

Page 21

Symbol English V Category voltage C V Category AC voltage C,RMS V Corona-discharge onset voltage CD V Charging voltage voltage DC V Fly-back capacitor voltage FB V Input voltage i V Output voltage o V Operating voltage ...

Page 22

Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...