si8600 Silicon Laboratories, si8600 Datasheet
si8600
Available stocks
Related parts for si8600
si8600 Summary of contents
Page 1
... All devices in this family include hot-swap, bidirectional SDA and/or SCL isolation channels with open-drain sink capability that operate to a maximum frequency of 1.7 MHz. The 8-pin version (Si8600) supports bidirectional SDA and SCL isolation; the Si8602 supports bidirectional SDA and unidirectional SCL isolation, and the 16-pin versions (Si8605, Si8606) feature two unidirectional isolation channels to support additional system signals, such as interrupts or resets ...
Page 2
Si860x 2 Rev. 1.0 ...
Page 3
T C ABLE O F ONTENTS Section 1. Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
... The maximum ambient temperature is dependent on data frequency, output loading, number of operating channels, and supply voltage. Table 2. Si860x Power Characteristics* 3.0 V < VDD < 5 –40 to +125 °C. Typical specs at 25 °C (See Figures 2 and 9 for test diagrams.) Parameter Symbol Si8600 Supply Current AVDD Current Idda BVDD Current Iddb AVDD Current ...
Page 5
... Iddb AVDD Current Idda BVDD Current Iddb *Note: All voltages are relative to respective ground. Table 3. Si8600/02/05/06 Electrical Characteristics for Bidirectional I 3.0 V < VDD < 5 –40 to +125 °C. Typical specs at 25 °C unless otherwise noted. Parameter Logic Levels Side A 2 Logic Input Threshold ...
Page 6
... Si860x Table 3. Si8600/02/05/06 Electrical Characteristics for Bidirectional I 3.0 V < VDD < 5 –40 to +125 °C. Typical specs at 25 °C unless otherwise noted. Parameter Timing Specifications (Measured at 1.40 V Unless Otherwise Specified) 2 Maximum I C Bus Frequency Propagation Delay 5 V Operation 4 Side A to Side B Rising 4 Side A to Side B Falling ...
Page 7
Table 4. Electrical Characteristics for Unidirectional Non-I 3.0 V < VDD < 5 –40 to +125 °C. Typical specs at 25 °C Parameter Symbol Positive-Going Input Threshold Negative-Going Input Threshold Input Hysteresis High Level Input Voltage Low ...
Page 8
Si860x Table 5. Electrical Characteristics for All I 3.0 V < VDD < 5 –40 to +125 °C. Typical specs at 25 °C Parameter VDD Undervoltage Threshold VDD Undervoltage Threshold VDD Negative-Going Lockout Hysteresis Common Mode Transient ...
Page 9
Test Circuits Figure 2 depicts the timing test diagram Figure 2. Simplified Timing Test Diagram Table 6. Regulatory Information* CSA The Si860x is certified under CSA Component Acceptance Notice 5A. For ...
Page 10
Si860x Table 7. Insulation and Safety-Related Specifications Parameter Symbol 1 L(1O1) Nominal Air Gap (Clearance) Nominal External Tracking L(1O2) 1 (Creepage) Minimum Internal Gap (Internal Clearance) Tracking Resistance (Proof Tracking Index) Erosion Depth 2 Resistance (Input-Output) 2 Capacitance (Input-Output) 3 ...
Page 11
Table 9. IEC 60747-5-2 Insulation Characteristics for Si86xxxx* Symbol Parameter Maximum Working Insulation V Voltage Input to Output Test Voltage V Transient Overvoltage Pollution Degree (DIN VDE 0110, Table 1) Insulation Resistance 500 V ...
Page 12
Si860x Table 11. Thermal Characteristics Parameter IC Junction-to-Air Thermal Resistance 400 300 270 200 160 100 0 0 Figure 3. NB SOIC-8 Thermal Derating Curve, Dependence of Safety Limiting Values with Case Temperature per DIN EN 60747-5-2 500 400 350 ...
Page 13
Figure 5. WB SOIC-16 Thermal Derating Curve, Dependence of Safety Limiting Values with Case Temperature per DIN EN 60747-5-2 Table 12. Absolute Maximum Ratings Parameter 2 Storage Temperature Ambient Temperature Under ...
Page 14
Si860x 2. Functional Description 2.1. Theory of Operation The operation of an Si86xx channel is analogous to that of an opto coupler, except an RF carrier is modulated instead of light. This simple architecture provides a robust isolated data path ...
Page 15
... Without anti-latch protection, bidirectional I through an adjacent isolator channel creating a stable latched low condition on both sides. Anti-latch protection is typically added to one side of the isolator to avoid this condition (the “A” side for the Si8600/02/05/06). The following examples illustrate typical circuit configurations using the Si8600/02/05/06. ...
Page 16
... C isolator is to choose which side of the bus will be connected to the isolator A side. Ideally, it should be the side which compatible with the range of bus pull up specified by the manufacturer. For example, the Si8600/02/05/06 isolators are normally used with a pull mA. 2. Has the highest input low level for devices on the bus. Some devices may specify an input low of 0.9 V and other devices might require an input low of 0 ...
Page 17
... Typical Application Schematics Figures 9 through 14 illustrate typical circuit configurations using the Si8600, Si8602, Si8605, and Si8606. AVDD 0.1 µ ASDA ASCL AGND Figure 9. Typical Si8600 Application Diagram AVDD 0.1 µF 3k ASDA ASCL AGND Figure 10. Typical Si8602 Application Diagram AGND AVDD 0.1 µ ...
Page 18
Si860x AGND AVDD 0.1 µF 3k ASDA ASCL AGND Figure 12. Typical Si8602 Application Diagram AVDD 0.1 µ ASDA RESET Micro- controller ASCL AGND Figure 13. Typical Si8605 Application Diagram AVDD 0.1 µ ASDA RESET INT ...
Page 19
Device Operation Device behavior during start-up, normal operation, and shutdown is shown in Figure 15, where UVLO+ and UVLO- are the positive-going and negative-going thresholds respectively. Refer to Table 14 to determine outputs when power supply (VDD) is not ...
Page 20
Si860x 4.3. Input and Output Characteristics for Non-I The unidirectional Si86xx inputs and outputs are standard CMOS drivers/receivers. The nominal output impedance of an isolator driver channel is approximately 50 , ±40%, which is a combination of the value of ...
Page 21
Layout Recommendations To ensure safety in the end user application, high voltage circuits (i.e., circuits with >30 V separated from the safety extra-low voltage circuits (SELV is a circuit with <30 V (creepage/clearance component, such as a ...
Page 22
Si860x 4.6. Typical Performance Characteristics The typical performance characteristics depicted in the following diagrams are for information purposes only. Refer to Tables and 5 for actual specification limits. Side A Side B 2 Figure 16 ...
Page 23
... AVDD Side A power supply terminal; connect to a source of 3 ASDA Side A data (open drain) input or output. 3 ASCL Side A clock input or output. Open drain I/O for Si8600. Standard CMOS input for Si8602. 4 AGND Side A ground terminal. 5 BGND Side B ground terminal. 6 BSCL Side B clock input or output. ...
Page 24
... Si860x AGND AVDD ASDA 5 ASCL 6 7 AGND NC 8 Table 16. Si8600/02 in Narrow and Wide-Body SOIC-16 Packages Pin Name 1 AGND Side A Ground Terminal connection. 3 AVDD Side A power supply terminal. Connect to a source of 3 connection. 5 ASDA Side A data open drain input or output. ...
Page 25
AVDD Bidirectional ASDA 3 Isolator Channel Unidirectional 4 ADIN Isolator Channel Unidirectional ADOUT 5 Isolator Channel ASCL Bidirectional 6 Isolator Channel NC 7 AGND 8 Si8605 Table 17. Si8605/06 in Narrow and Wide-Body SOIC-16 Packages Pin Name ...
Page 26
... Si8602AC-B-IS 1 Si8602AD-B-IS 1 Si8605AC-B-IS1 2 Si8605AD-B-IS 2 Si8606AC-B-IS1 2 Si8606AD-B-IS 2 2,3 Revision A Devices Si8600AC-A-IS 2 Si8600AD-A-IS 2 Si8602AC-A-IS 1 Si8602AD-A-IS 1 Si8605AC-A-IS1 2 Si8605AD-A-IS 2 Si8606AC-A-IS1 2 Si8606AD-A-IS 2 Notes: 1. All packages are RoHS-compliant. Moisture sensitivity level is MSL3 with peak reflow temperature of 260 °C according to the JEDEC industry standard classifications and peak solder temperature. ...
Page 27
Package Outline: 16-Pin Wide Body SOIC Figure 21 illustrates the package details for the Si860x Digital Isolator. Table 19 lists the values for the dimensions shown in the illustration. Table 19. Package Diagram Dimensions Figure 21. 16-Pin Wide Body ...
Page 28
Si860x 8. Land Pattern: 16-Pin Wide-Body SOIC Figure 22 illustrates the recommended land pattern details for the Si860x in a 16-pin wide-body SOIC. Table 20 lists the values for the dimensions shown in the illustration. Table 20. 16-Pin Wide Body ...
Page 29
Package Outline: 8-Pin Narrow Body SOIC Figure 23 illustrates the package details for the Si860x in an 8-pin SOIC (SO-8). Table 21 lists the values for the dimensions shown in the illustration. Figure 23. 8-pin Small Outline Integrated Circuit ...
Page 30
Si860x 10. Land Pattern: 8-Pin Narrow Body SOIC Figure 24 illustrates the recommended land pattern details for the Si860x in an 8-pin narrow-body SOIC. Table 22 lists the values for the dimensions shown in the illustration. Figure 24. PCB Land ...
Page 31
Package Outline: 16-Pin Narrow Body SOIC Figure 25 illustrates the package details for the Si860x in a 16-pin narrow-body SOIC (SO-16). Table 23 lists the values for the dimensions shown in the illustration. Figure 25. 16-pin Small Outline Integrated ...
Page 32
Si860x Table 23. Package Diagram Dimensions (Continued) Dimension h θ aaa bbb ccc ddd Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to the JEDEC ...
Page 33
Land Pattern: 16-Pin Narrow Body SOIC Figure 26 illustrates the recommended land pattern details for the Si860x in a 16-pin narrow-body SOIC. Table 24 lists the values for the dimensions shown in the illustration. Figure 26. 16-Pin Narrow Body ...
Page 34
Si860x 13. Top Marking: 16-Pin Wide Body SOIC Base Part Number Line 1 Marking: Ordering Options (See Ordering Guide for more information). Line 2 Marking Year WW = Workweek TTTTTT = Mfg Code Circle = 1.5 mm Diameter ...
Page 35
Top Marking: 8-Pin Narrow Body SOIC Figure 28. 8-Pin Narrow Body SOIC Top Marking Table 26. 8-Pin Narrow Body SOIC Top Marking Table Line 1 Marking: Base Part Number Ordering Options (See Ordering Guide for more information). Line 2 ...
Page 36
Si860x 15. Top Marking: 16-Pin Narrow Body SOIC Figure 29. 16-Pin Narrow Body SOIC Top Marking Table 27. 16-Pin Narrow Body SOIC Top Marking Table Line 1 Marking: Base Part Number Ordering Options Line 2 Marking: Circle = 1.2 mm ...
Page 37
... Si8601 replaced by Si8602 throughout. Added chip graphics on page 1. Moved Table 12 to page 13. Updated Table 3, “Si8600/02/05/06 Electrical Characteristics for Bidirectional I2C Channels page 5. Updated Table 7, “Insulation and Safety-Related Specifications,” on page 10. Updated Table 9, “IEC 60747-5-2 Insulation Characteristics for Si86xxxx*,” ...
Page 38
... Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where per- sonal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized ap- plication, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages ...