d11-en6-fp-q Banner Engineering Corp., d11-en6-fp-q Datasheet - Page 4
![no-image](/images/no-image-200.jpg)
d11-en6-fp-q
Manufacturer Part Number
d11-en6-fp-q
Description
Series D11 Expert With Automatic Sensitivity Adjustment
Manufacturer
Banner Engineering Corp.
Datasheet
1.D11-EN6-FP-Q.pdf
(4 pages)
Photoelectric sensors
Series D11 Expert
with automatic
sensitivity adjustment
Programming of the D11 Expert
From the RUN MODE the D11 Expert can be switched to:
•
•
In addition, the D11 Expert provides two special features:
•
•
Contrast indication
1
) A wide range of glass- and plastic fibre-optics can be found
Number of flashes
TEACH MODE: to optimize the sensitivity adjustment of the
sensor (see programming sequence at right). After a
TEACH sequence, the unit will automatically return to the
RUN mode.
OUTPUT PULSE STRETCHER: to enable or disable a 40
ms OFF delay (see programming sequence at right)
disabling the push button on the D11 Expert sensor: this
can be done by pulsing the remote input 4 consecutive
times. To enable the use of the button again, pulse the
remote input again 4 consecutive times.
maximum sensitivity setting: the D11 Expert is factory pro-
grammed for maximum sensitivity. To recall the default set-
ting, push and hold the push button for two or more sec-
onds, then click the button 4 consecutive times. This will
also enable light operate output and pulse stretcher „off“
settings.
in the Photoelectric Catalogue.
Detection mode with typical
plastic fibre-optic
Opposed
Diffuse
!
1
2
3
4
IMPORTANT SAFETY WARNING ! These sensors do NOT include the self-checking redundant circuitry necessary
to allow their use in personnel safety applications. A sensor failure or malfunction can result in either an energised or
de-energised output condition. These products should not be used as sensing devices for personnel safety.
1
)
with PIT26U
with PIT46U
with PIT26U
with PIT46U
with PBT26U
with PBT46U
with PBT26U
with PBT46U
Contrast
unacceptable
low
moderate
high
180 mm
180 mm
50 mm
50 mm
10 mm
50 mm
10 mm
50 mm
red
red
red
red
Subject to changes without notice • Edition 11.98/1 P/N ED006K8A
pnp
pnp
npn
npn
Push-button
push and hold for
double-click
single-click
double-click
Teach Mode Programming
Output pulse stretcher
Push-button
push and hold for
single-click
single-click
2 s
2 s
connector D11-EP6-FP-Q
connector D11-EN6-FP-Q
cable
cable
Mode/function
from RUN to output
programming
show current status
of pulse stretcher
toggles between
pulse stretcher „on“
or „off“
save configuration and standard RUN mode
return to RUN mode
Mode/function
from RUN to TEACH
mode
TEACH „on“ condition G: flashing at 2 Hz
detection of first
sensing condition
TEACH „off“ condition G, Y and R LED‘s flash
detection of second
sensing condition
Returns automatically sensing contrast (see
to RUN mode
D11-EP6-FP
D11-EN6-FP
Indicator LEDs
G: flashing at 1 Hz
Y: off
R: pulsing (denotes
G: off
Y: off
R: - double flash denotes
Indicator LEDs
G: flashing at 1 Hz
Y: off
R: pulsing (denotes
Y: off
R: pulsing (denotes
simultaneously 1 to 4
times to indicate the
table)
signal strength)
- on steadily denotes
signal strength)
signal strength)
pulse stretcher „off“
pulse stretcher „on“
30 442 74
30 442 76
30 442 71
30 442 73