ltl2r3krk-002 LiteOn Technology Corp., ltl2r3krk-002 Datasheet
ltl2r3krk-002
Available stocks
Related parts for ltl2r3krk-002
ltl2r3krk-002 Summary of contents
Page 1
... Tolerance is ± 0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 2
... Derating Linear From 50 ℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25 ℃ ℃ ℃ ℃ A Maximum Rating ...
Page 3
... The dominant wavelength, λ derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 5. The Iv guarantee should be added ± 15%. Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION =25 ℃ ...
Page 4
... Typical Electrical / Optical Characteristics Curves (25 ℃ Ambient Temperature Unless Otherwise Noted) Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : ...
Page 5
... Feed Hole Pitch Lead Location Center of Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Symbol D F △ ...
Page 6
... Inner cartons per outer carton total 12000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing. Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION ...
Page 7
... Note: Tolerance of each bin limit is ± 15% Dominant Wavelength Bin Code H29 H30 H31 H32 H33 Note: Tolerance of each bin limit is ± 1nm Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Unit : mcd @20mA Min. 310 400 520 ...
Page 8
... Soldering time 3 sec. Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION CAUTIONS ...
Page 9
... The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Chip ESD level InGaN / Sapphire AlInGaP InGaN / SiC Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Circuit model B ...
Page 10
... All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Page : 10 ...
Page 11
... Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL2R3KRK-002 BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) Ta= 65± ...