ltl1chkeknn-bb LiteOn Technology Corp., ltl1chkeknn-bb Datasheet
ltl1chkeknn-bb
Available stocks
Related parts for ltl1chkeknn-bb
ltl1chkeknn-bb Summary of contents
Page 1
... Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice Free on electrode pins coated by the soldering material 99.9% Sn. Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Lens Source Color Water Clear ...
Page 2
... Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 65℃ Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [1.6mm(.063") From Body] Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 =25℃ A Maximum Rating 0.75 5 -40 ℃ ...
Page 3
... Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 =25℃ A Symbol Min ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION Typical Electrical / Optical Characteristics Curves (25 ℃ Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Ambient Temperature Unless Otherwise Noted) Page : ...
Page 5
... Top of Component to Seating Plane Lead Length After Component Height Feed Hole Pitch Lead Location Center of Component Location Total Taped Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Specification Symbol Minimum mm inch mm D 3.8 ...
Page 6
... Note: Tolerance of each bin limit is ±15% Dominant Wavelength Bin Code H27 H28 H29 H30 H31 Note: Tolerance of each bin limit is ±1nm Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Unit : mcd @20mA Min. Max. 240 400 400 680 680 1150 1150 1900 Unit : nm @20mA Min ...
Page 7
... 2500 pcs per inner carton 10 Inner cartons per outer carton total 25000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Packing Spec Page : 7 ...
Page 8
... Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 CAUTIONS Wave soldering Pre-heat 100° ...
Page 9
... Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Circuit model B ...
Page 10
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Page : ...
Page 11
... Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL1CHKEKNN-BB (FOR MATSUSHITA W/M) BNS-OD-C131/A4 Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) Ta= 65±5℃ ...