ltl1khkgknn-002 LiteOn Technology Corp., ltl1khkgknn-002 Datasheet
ltl1khkgknn-002
Related parts for ltl1khkgknn-002
ltl1khkgknn-002 Summary of contents
Page 1
... Tolerance is ±0.25mm(.010") unless otherwise noted. 3. Protruded resin under flange is 1.0mm(.04") max. 4. Lead spacing is measured where the leads emerge from the package. 5. Specifications are subject to change without notice. 6. The LED lamp original is LTL1KHKGKNN Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Lens Source Color Water Clear ...
Page 2
... Power Dissipation Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Width) DC Forward Current Derating Linear From 50°C Reverse Voltage Operating Temperature Range Storage Temperature Range Lead Soldering Temperature [2mm (.0787") From Body] Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 =25C ˚ A Maximum Rating 0.4 5 -40° 100°C -55° ...
Page 3
... Iv classification code is marked on each packing bag. 4. The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 =25 ˚ Symbol Min ...
Page 4
... LITE-ON TECHNOLOGY CORPORATION Typical Electrical / Optical Characteristics Curves (25˚C Ambient Temperature Unless Otherwise Noted) Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Page : ...
Page 5
... Feed Hole to Overall Component Height Lead Length After Component Height Feed Hole Pitch Lead Location Center of Component Location Total Tape Thickness Feed Hole Location Adhesive Tape Width Adhesive Tape Position Tape Width Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Specification Minim Symbol mm inch D 3.8 0.149 F 2 ...
Page 6
... reel per inner carton total 3000pcs per inner carton 6 Inner cartons per outer carton total 18000 pcs per outer carton In every shipping lot, only the last pack will be non-full packing Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Packing Spec Page : 6 of ...
Page 7
... Note: Tolerance of each bin limit is ±15% Dominant Wavelength Bin Code H06 H07 H08 H09 H10 H11 Note: Tolerance of each bin limit is ±1nm Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Unit : mcd @20mA Min. Max. 85 110 110 140 140 180 180 240 240 ...
Page 8
... Soldering time 3 sec. Max. (one time only) Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR reflow is not suitable process for through hole type LED lamp product. Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 CAUTIONS Wave soldering Pre-heat 100° ...
Page 9
... Work tables, storage racks, etc. should be properly grounded Use ion blower to neutralize the static charge which might have built up on surface of the LEDs plastic lens as a result of friction between LEDs during storage and handing Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Circuit model B LED ...
Page 10
... No static charge generators (e.g. plastics) inside shielding containers with ESDS items? 4. All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Page : ...
Page 11
... Environmental Test Solder Resistance Solderability 9. Others The appearance and specifications of the product may be modified for improvement, without prior notice. Part No. : LTL1KHKGKNN-002 BNS-OD-C131/A4 Test Condition Ta= Under Room Temperature As Per Data Sheet Maximum Rating *Test Time= 1000HRS (-24HRS,+72HRS) Ta= 65±5°C RH= 90 ～ ...