ltl912qeks LiteOn Technology Corp., ltl912qeks Datasheet
ltl912qeks
Available stocks
Related parts for ltl912qeks
ltl912qeks Summary of contents
Page 1
... Selection Guide Part No. LTL912QEKS Benefits Fewer LEDs Required Lower lighting System Cost Applications Automotive exterior lighting Electronic sign and signals Part No. : LTL912QEKS BNS-OD-C131/A4 LITE-ON TECHNOLOGY CORPORATION Color Φv (lm) Red 1.8 Va(deg.) λ ...
Page 2
... LED materials etc., which allow designers to match the color of popular lighting applications, such as automotive lighting and electronic signs. Devices Part No. LTL912QEKS Part No. : LTL912QEKS BNS-OD-C131/ Lens Source Color Water Clear ...
Page 3
... All dimensions are in millimeters (inches). 2. Protruded resin is 1.0mm(.04") max. 3. Lead spacing is measured where the leads emerge from the package. 4. Specifications are subject change to without notice. Part No. : LTL912QEKS BNS-OD-C131/ Page : ...
Page 4
... R Operating Temperature Range Storage Temperature Range LED Junction Temperature Soldering Preheat Temperature Lead Soldering Temperature Notes: 1. Operation at currents below 10mA is not recommended. Part No. : LTL912QEKS BNS-OD-C131/ Maximum Rating 190 130 70 1.17 10 -40° ...
Page 5
... The dominant wavelength, λd is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. Part No. : LTL912QEKS BNS-OD-C131/ =25℃ ...
Page 6
... LITE-ON TECHNOLOGY CORPORATION Typical Electrical / Optical Characteristics Curves (25°C Ambient Temperature Unless Otherwise Noted) Part No. : LTL912QEKS BNS-OD-C131/ Page : ...
Page 7
... LITE-ON TECHNOLOGY CORPORATION Bin Code List For Reference Part No. : LTL912QEKS BNS-OD-C131/ Page : ...
Page 8
... Dim: 520mm x 9.6mm x 13.3mm 2. Inner carton: 153 tubes x 65 pcs = 9,945 pcs Dim: 530mm x 175mm x 128mm 3. Outer carton: 4 inner cartons x 9,945 pcs = 39,780 pcs Dim: 545mm x 370mm x 280mm Part No. : LTL912QEKS BNS-OD-C131/ Page : 8 ...
Page 9
... Note: Excessive soldering temperature and/or time might result in deformation of the LED lens or catastrophic failure of the LED. IR re-flow is not suitable process for through whole type Piranha LED production. Part No. : LTL912QEKS BNS-OD-C131/ ...
Page 10
... To verify for ESD damage, check for “light up” and Vf of the suspect LEDs at low currents. The Vf of “good” LEDs should be >2.0V@0.1mA for InGaN product and >1.4V@0.1mA for AlInGaP product. Part No. : LTL912QEKS BNS-OD-C131/ ...
Page 11
... All flexible conductive and dissipative package materials inspected before reuse or recycle? Others 1. Audit result reported to entity ESD control coordinator? 2. Corrective action from previous audits completed? 3. Are audit records complete and on file? Part No. : LTL912QEKS BNS-OD-C131/ Page : 11 ...
Page 12
... Liteon may make process or materials changes affecting the performance or other characteristics of our products. These products supplied after such changes will continue to meet published specifications, but may not be identical to products supplied as samples or under prior orders. Part No. : LTL912QEKS BNS-OD-C131/ ...