ir3800 International Rectifier Corp., ir3800 Datasheet
ir3800
Related parts for ir3800
ir3800 Summary of contents
Page 1
... The onboard switching controller and MOSFETs make the IR3800 a space-efficient solution, providing accurate power delivery for low output voltage applications. The IR3800 operates from a single 4.5V to 14V input supply and generates an output voltage adjustable from 0.6V to 0.75*Vin at loads up to 12A. A versatile regulator offering programmability of startup time and current limit, the IR3800’ ...
Page 2
... PGnd AGnd COMP AGnd AGnd SS OCSet Fig. 2: Package outline (Top view) PACKAGE PIN COUNT DESCRIPTION IR3800MTRPbF 15 IR3800MTR1PbF 15 PD-60352 IR3800MPbF o C θ θ PCB - PARTS PER REEL 4000 750 2 ...
Page 3
... Block Diagram Fig. 3. Simplified block diagram of the IR3800. 11/04/08 PD-60352 IR3800MPbF 3 ...
Page 4
... This pin powers the high side driver and must be connected to a voltage C higher than input voltage. A minimum of 0.1uF high frequency capacitor must be connected from this pin to the power ground (PGnd). 15 AGnd Signal ground for internal reference and control circuitry. Pins 4, 5 and 15 need to be connected together on system board. 11/04/08 IR3800MPbF Description PD-60352 4 ...
Page 5
... V =1.8V, Io=0A o SS=3V, V =24V =12V =1.8V, Io=0A o Supply ramping up Supply ramping down Supply ramping up and down Supply ramping up Supply ramping down Supply ramping up and down PD-60352 IR3800MPbF Max Units 125 =12V, 0 C<T (Ic)<105 Min TYP ...
Page 6
... Note2: Cold temperature performance is guaranteed via correlation using statistical quality control. Not tested in production. Note3: Guaranteed by Design but not tested in production. 11/04/08 Test Condition Min 540 Note3 Note3 Fb=0V 75 SS=3V SS= 1000 SS= Note3 , Note3 Hiccup SS Note3 Note3 PD-60352 IR3800MPbF TYP MAX Units 600 660 kHz 1. -0.1 -0 μ μmho 1300 1600 μ 0. μ ...
Page 7
... PD-60352 IR3800MPbF 125 C) Ic(static 100 120 Temp[oC] Ic(dynam ic 100 120 Tem p[oC] ISS 100 120 Tem p[oC] IOCSET 100 120 Tem p[oC] 7 ...
Page 8
... There hysteresis in the thermal shutdown threshold. 11/04/08 mode PWM Pre-Bias Startup The IR3800 is able to start up into pre-charged output, which disturbances of the output voltage. The output starts in asynchronous fashion and keeps the synchronous MOSFET off until the first gate signal for control MOSFET is generated ...
Page 9
... Soft-Start The IR3800 has programmable soft-start to control the output voltage rise and limit the inrush current during start-up. To ensure correct start-up, sequence initiates when Vcc and Vc rise above their threshold and generate the Power On Ready (POR) signal. The soft-start function operates by sourcing current to charge an external capacitor to about 3V ...
Page 10
... Fig. 9: OCset pin during normal condition Ch1: Inductor point, Ch3:OCSet --( 3 ) The value of R circuit to ensure that the over-current protection circuit activates as expected. The IR3800 current limit is designed primarily as disaster preventing, and doesn't operate as a precision current regulator. PD-60352 IR3800MPbF Deadtime Blanking time ...
Page 11
... R ⎝ ⎠ 9 When an external resistor divider is connected to the output as shown in figure 10. V OUT IR3624 IR3800 Fb Fig. 10: Typical application of the IR3800 for programming the output voltage Equation (4) can be rewritten as: ⎛ ⎞ V ⎜ ⎜ ⎟ ⎟ = ∗ --( ) 5 ref − ...
Page 12
... The overall performance of the converter and determine the result of transient response, selection of the capacitor is critical. The IR3800 can perform well with all types of capacitors. can rule the capacitor must have low enough ESR to meet output ripple and load transient requirements, yet have high enough ESR to satisfy stability requirements ...
Page 13
... Feedback Compensation The IR3800 is a voltage mode controller; the control loop is a single voltage feedback path including error amplifier and error comparator. To achieve fast transient response and accurate output regulation, a compensation circuit is necessary. The goal of the compensation network is to provide a closed loop transfer ...
Page 14
... R R Cross over frequency is expressed as ⎤ ⎞ ⎟ ⎟ ⎥ ⎠ ⎦ PD-60352 IR3800MPbF OUT E Comp 9 V REF Frequency (current source) ...
Page 15
... Select : π ref * ref PD-60352 IR3800MPbF ( ) 1 for Θ max = F and F 0 ≥ o OSC , KΩ , check Ω : ...
Page 16
... Place the input capacitor directly to - -(3) the Vin pin of IR3800. To reduce the ESR replace the single input capacitor with two parallel units. The feedback part of the system should be kept away from the inductor and other noise sources. ...
Page 17
... Typical Application for IR3800 Fig.16: Typical Application circuit for 12V to 1.8V at 12A using ceramic output capacitors 11/04/08 12V to 1.8V @ 12A PD-60352 IR3800MPbF 17 ...
Page 18
... The pad lands (the 4 big pads other than the 11 IC pins) length and width should be equal to maximum part pad length and width. However, the minimum metal to metal spacing should be no less than 0.17mm for 2 oz. Copper; no less than 0.1mm for 1 oz. Copper and no less than 0.23mm for 3 oz. Copper. 11/04/08 PD-60352 IR3800MPbF 18 ...
Page 19
... Ensure that the solder resist in between the lead lands and the pad land is ≥ 0.15mm due to the high aspect ratio of the solder resist strip separating the lead lands from the pad land. 11/04/08 PD-60352 IR3800MPbF 19 ...
Page 20
... The maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. 11/04/08 PD-60352 IR3800MPbF 20 ...
Page 21
... This product has been designed and qualified for the Consumer market. 11/04/08 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 Visit us at www.irf.com for sales contact information Data and specifications subject to change without notice. 10/07 PD-60352 IR3800MPbF TAC Fax: (310) 252-7903 21 ...