lt1941 Linear Technology Corporation, lt1941 Datasheet - Page 8

no-image

lt1941

Manufacturer Part Number
lt1941
Description
Triple Monolithic Switching Regulator
Manufacturer
Linear Technology Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lt1941EFE
Manufacturer:
MAX
Quantity:
95
Part Number:
lt1941EFE
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
lt1941EFE#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
lt1941EFE#TRPBF
Manufacturer:
JRC
Quantity:
1 000
Part Number:
lt1941EFE#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
BLOCK DIAGRA
LT1941
The LT1941 is a constant frequency, current mode, triple
output regulator with internal power switches. The three
regulators share common circuitry including input source,
voltage reference and oscillator, but are otherwise inde-
pendent. Operation can be best understood by referring to
the Block Diagram.
If the RUN/SS pins are tied to ground, the LT1941 is shut
down and draws 50µA from the input source tied to V
Internal 2µA current sources charge external soft-start
capacitors, generating voltage ramps at these pins. If any
of the RUN/SS pins exceed 0.6V, the internal bias circuits
turn on, including the internal regulator, reference and
1.1MHz master oscillator. Each switching regulator will
only begin to operate when its corresponding RUN/SS pin
reaches ≈1V. The master oscillator generates three clock
signals, with the two signals for the step-down regulators
out of phase by 180°.
The three switchers are current mode regulators. Instead
of directly modulating the duty cycle of the power switch,
the feedback loop controls the peak current in the switch
during each cycle. Compared to voltage mode control,
current mode control improves loop dynamics and pro-
vides cycle-by-cycle current limit.
The Block Diagram shows only one of the two step-down
switching regulators. A pulse from the slave oscillator
sets the RS flip-flop and turns on the internal NPN bipolar
power switch. Current in the switch and the external
inductor begins to increase. When this current exceeds a
level determined by the voltage at V
C1 resets the flip-flop, turning off the switch. The current
in the inductor flows through the external Schottky diode
and begins to decrease. The cycle begins again at the next
pulse from the oscillator. In this way, the voltage on the
V
output. The internal error amplifier regulates the output
voltage by continually adjusting the V
threshold for switching on the V
clamp of 1.7V limits the output current. The RUN/SS pin
voltage also clamps the V
current source charges the external soft-start capacitor,
the current limit increases slowly. An internal op amp
allows the part to regulate negative voltages using only
two external resistors.
8
C
pin controls the current through the inductor to the
W
C
pin voltage. As the internal
C
pin is ≈1V and an active
C
, current comparator
C
pin voltage. The
IN
.
Each switcher contains an extra, independent oscillator to
perform frequency foldback during overload conditions.
This slave oscillator is normally synchronized to the mas-
ter oscillator. A comparator senses when V
50% of its regulated value and switches the regulator from
the master oscillator to a slower slave oscillator. The V
pin is less than 50% of its regulated value during start-up,
short circuit and overload conditions. Frequency foldback
helps limit switch current under these conditions.
The switch drivers for SW1 and SW2 operate either from
V
diode are used to generate a voltage at the BOOST pin that
is higher than the input supply. This allows the driver to
saturate the internal bipolar NPN power switch for efficient
operation.
The BIAS1 pin allows the internal circuitry to draw its
current from a lower voltage supply than the input, also
reducing power dissipation and increasing efficiency. If
the voltage on the BIAS1 pin falls below 2.35V, then its
quiescent current will flow from V
The BIAS2 pin allows the driver for SW3 to draw its
current from a lower voltage supply than the input. This
reduces power dissipation within the part and increases
efficiency. If the voltage on the BIAS2 pin falls below ≈2V,
then SW3 will lock out and will not be able to turn on until
BIAS2 rises above ≈2.1V.
A power good comparator trips when the FB pin is at 91%
of its regulated value. The PGOOD output is an open-
collector transistor that is off when the output is in
regulation, allowing an external resistor to pull the PGOOD
pin high. Power good is valid when the LT1941 is enabled
and V
Input power good comparators monitor the input supply.
The 5GOOD and 12GOOD pins are open-collector outputs
of internal comparators. The 5GOOD pin remains low until
the input is within 10% of 5V. The 12GOOD pin remains
low until the input is within 10% of 12V. The 5GOOD and
12GOOD pins are valid as long as V
Both the 5GOOD and 12GOOD pins will sink current when
the part is in shutdown, independent of the voltage at V
IN
or from the BOOST pin. An external capacitor and
IN
> 3.5V.
IN
IN
.
is greater than 1.1V.
FB
is less than
1941fa
IN.
FB

Related parts for lt1941