ltc3523-ltc3523-2 Linear Technology Corporation, ltc3523-ltc3523-2 Datasheet - Page 8

• Manufacturer Part Number: ltc3523-ltc3523-2
• Description: Synchronous 600ma Step-up And 400ma Step-down Dc/dc Converters
• Manufacturer: Linear Technology Corporation

LTC3523/LTC3523-2
The LTC3523 and LTC3523-2 are synchronous step-up and
step-down converters housed in a 16-pin QFN package.
Operating from inputs down to 1.8V, the devices feature
fi xed frequency, current mode PWM control for exceptional
line and load regulation and transient response. With
low R
maintain high effi ciency over a wide range of load cur-
rent. Operation can be best understood by referring to
the Block Diagram.
Soft-Start
Both the step-up and step-down converters on the LTC3523
/LTC3523-2 provide soft-start. The soft-start time is typi-
cally 500μs. The soft-start function resets in the event of
a commanded shutdown or thermal shutdown.
Oscillator
The frequency of operation is set by an internal oscilla-
tor to a nominal 1.2MHz for the LTC3523 and nominal
2.4MHz for the LTC3523-2. The oscillator is shared by
both converters.
Shutdown
The step-up and the step-down converters have inde-
pendent shutdown pins. To shut down a converter, pull
⎯ S ⎯ H ⎯ D ⎯ N ⎯ x below 0.35V. To enable a converter, pull ⎯ S ⎯ H ⎯ D ⎯ N ⎯ x
above 1.0V.
Error Amplifi ers
Power converter control loop compensation is provided
internally for each converter. The noninverting input is
internally connected to the 1.2V reference for the step-up
and 0.6V for the step-down. The inverting input is connected
to the respective FBx for both converters. Internal clamps
limit the minimum and maximum error amp output voltage
for improved large signal transient response. A voltage
divider from V
via the respective FBx pins from 1.8V to 5.25V for the step-
up and 0.615V to 5.5V for the step-down. From the Block
Diagram the design equation for programming the output
voltages is V
V
OPERATION
8
OUT
= 0.6V • [1 + (R3/R4)] for the step-down.
DS(ON)
OUT
and internal MOSFET switches, the devices
OUT
= 1.2V • [1 + (R1/R2)] for the step-up and
to ground programs the output voltage
PWM Comparators
The PWM comparators are used to compare the converters
external inductor current to the current commanded by
the error amplifi ers. When the inductor current reaches
the current commanded by the error amplifi er the induc-
tor charging cycle is terminated and the rectifi cation cycle
commences.
Current Limit
The current limit comparator shuts off the N-channel switch
for the step-up and P-channel switch for the step-down
once its current limit threshold is reached. The current
limit comparator delay to output is typically 40ns. Peak
switch current is limited to approximately 900mA for the
step-up and 650mA for the step-down independent of
input or output voltage.
Zero Current Comparator
The zero current comparator monitors the inductor cur-
rent to the output and shuts off the synchronous rectifi er
once this current reduces to approximately 20mA. This
prevents the inductor current from reversing in polarity
improving effi ciency at light loads.
Power Good Comparator
Both converters have independent open drain power good
comparators which monitor the output voltage via their
respective FBx pins. The comparator output will allow the
PGOODx to be pulled up high when the output voltage
(V
voltage decreases below 91%, the comparator will pull
the PGOODx pin to ground. The step-up comparator has
3.3% of hysteresis and the step-down has 6.6% relative
to FBx voltage for added noise immunity.
Step-Down Overvoltage Comparator
The step-down overvoltage comparator guards against
transient overshoots greater than 10% of the output volt-
age by turning the P-channel switch off until the transient
has subsided.
OUT
) has exceeded 91% of it fi nal value. If the output
3523f