mc10e1651 ON Semiconductor, mc10e1651 Datasheet - Page 3

• Manufacturer Part Number: mc10e1651
• Description: 5 V, -5 V Dual Ecl Output Comparator With Latch
• Manufacturer: ON Semiconductor

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
1. Input V
2. VCMR Min varies 1:1 with V
3. Hysteresis skew (V
Table 3. MAXIMUM RATINGS
Table 4. DC CHARACTERISTICS
V
V
V
I
T
T
q
q
V
T
V
V
V
V
II
I
I
I
VCMR
Hys
V
C
Symbol
Symbol
out
IH
CC
EE
A
stg
JA
JC
sol
SUP
PP
I
EE
OH
OL
IL
IH
skew
in
27 mV and the V
hysteresis window ranged from 14 mV below the reference level to 13 mV above the reference level. All hysteresis measurements were
determined using a reference voltage of 0 mV.
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
IL
and V
Output HIGH Voltage (Note 1)
Output Low Voltage (Note 1)
Input LOW Voltage (LEN) (Note 1)
Input HIGH Voltage (LEN) (Note 1)
Input Current (V1, V2)
Input HIGH Current (LEN)
Positive Supply Current
Negative Supply Current
Common Mode Range (Note 2)
Hysteresis
Hysteresis Skew (Note 3)
Input Capacitance
Total Supply Voltage
Differential Input Voltage
Input Voltage
Output Current
Operating Temperature Range
Storage Temperature Range
Thermal Resistance (Junction-to-Ambient)
Thermal Resistance (Junction-to-Case)
Operating Range
Wave Solder
IH
skew
parameters vary 1:1 with V
skew
value indicates that the hysteresis was skewed from the reference level by 1mV in the negative direction. Hence the
Characteristic
) is provided to indicate the offset of the hysteresis window. For example, at 25°C the nominal hysteresis value is
Parameter
EE
; Max varies 1:1 with V
V
CC
= +5.0 V ±5%; V
CC
PLCC
Pb-Free
DIP
. Output V
Pb
-1020
-1950
CC
-1.95
-1.17
-2.0
Min
http://onsemi.com
.
|V
|V1 - V2|
Continuous
Surge
0 lfpm
500 lfpm
Standard Board
GND = 0 V
v 3 sec @ 248°C
v 3 sec @ 260°C
OH
MC10E1651
EE
EE
Condition 1
| + |V
and V
= -5.2 V ±5%, GND = 0 V (Note 1)
-1.0
0°C
Typ
27
3
CC
OL
|
-1630
-1.48
-0.84
parameters vary 1:1 with GND.
-840
Max
150
-55
3.0
65
50
3
2
-1950
-1.95
-1.13
-980
-2.0
Min
28 PLCC
28 PLCC
28 PLCC
Condition 2
25°C
-1.0
Typ
27
-1630
-1.48
-0.81
-810
Max
150
-55
3.0
65
50
3
2
-1950
-1.95
-1.07
-920
-2.0
Min
V
EE
-65 to +150
-4.2 to -5.7
0 to +85
22 to 26
v V
Rating
12.0
63.5
43.5
100
265
265
3.7
85°C
50
Typ
30
0
I
v V
-0.735
CC
-1600
-1.45
-735
Max
150
-55
3.0
65
50
3
2
°C/W
°C/W
°C/W
Unit
mA
mA
°C
°C
°C
Unit
V
V
V
V
mV
mV
mV
mV
mA
mV
mV
mA
pF
V