m74hc573 STMicroelectronics, m74hc573 Datasheet
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
m74hc573
Available stocks
Related parts for m74hc573
m74hc573 Summary of contents
Page 1
... V (OPR PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 573 DESCRIPTION The M74HC573 is an high speed CMOS OCTAL LATCH WITH 3-STATE OUTPUTS fabricated 2 with silicon gate C MOS technology. This 8-BIT D-Type latches is controlled by a latch enable input (LE) and output enable input (OE). ...
Page 2
... M74HC573 INPUT AND OUTPUT EQUIVALENT CIRCUIT TRUTH TABLE Don’t Care Z: High Impedance (*): Q Outputs are latched at the time when the LE input is taken low logic level. LOGIC DIAGRAM 2/12 PIN DESCRIPTION PIN 12, 13, 14, 15, 16, 17, ...
Page 3
... Supply Voltage CC V Input Voltage I V Output Voltage O T Operating Temperature op Input Rise and Fall Time Parameter Parameter 6.0V CC M74HC573 Value Unit - 500(*) mW -65 to +150 °C 300 °C ...
Page 4
... M74HC573 DC SPECIFICATIONS Symbol Parameter V CC (V) V High Level Input 2.0 IH Voltage 4.5 6.0 V Low Level Input 2.0 IL Voltage 4.5 6.0 V High Level Output 2.0 OH Voltage 4.5 6.0 4.5 6.0 V Low Level Output 2.0 OL Voltage 4.5 6.0 4.5 6.0 I Input Leakage I 6.0 Current I High Impedance OZ Output Leakage 6.0 Current I Quiescent Supply CC 6.0 Current 4/12 Test Condition T = 25° Min. Typ. 1.5 3.15 4 ...
Page 5
... 150 M74HC573 Value -40 to 85°C -55 to 125° C Unit Max. Min. Max. Min. Max 115 145 175 155 195 ...
Page 6
... M74HC573 CAPACITIVE CHARACTERISTICS Symbol Parameter V CC (V) C Input Capacitance IN Output C OUT Capacitance C Power Dissipation PD Capacitance (note defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without PD load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. I ...
Page 7
... WAVEFORM PROPAGATION DELAYS, LE MINIMUM PULSE WIDTH SETUP AND HOLD TIMES (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIMES (f=1MHz; 50% duty cycle) M74HC573 7/12 ...
Page 8
... M74HC573 WAVEFORM 3: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) 8/12 ...
Page 9
... Plastic DIP-20 (0.25) MECHANICAL DATA mm. DIM. MIN. TYP a1 0.254 B 1.39 b 0. 8.5 e 2.54 e3 22. 3.3 Z inch MAX. MIN. TYP. 0.010 1.65 0.055 0.018 0.010 25.4 0.335 0.100 0.900 7.1 3.93 0.130 1.34 M74HC573 MAX. 0.065 1.000 0.280 0.155 0.053 P001J 9/12 ...
Page 10
... M74HC573 DIM. MIN 0 0. 12.60 E 10. 7. 10/12 SO-20 MECHANICAL DATA mm. TYP MAX. MIN. 2.65 0.2 0.004 2.45 0.49 0.014 0.32 0.009 0.5 45° ( typ.) 13.00 0.496 10.65 0.393 1.27 11.43 7.60 0.291 1.27 0.020 0.75 8° (max.) inch TYP. MAX. 0.104 0.008 0.096 0.019 0.012 0.020 0.512 0.419 0.050 0.450 0.300 0.050 ...
Page 11
... A1 PIN 1 IDENTIFICATION 1 MAX. MIN. 1.2 0.15 0.002 1 1.05 0.031 0.30 0.007 0.20 0.004 6.6 0.252 6.6 0.244 4.48 0.169 8° 0° 0.75 0.018 M74HC573 inch TYP. MAX. 0.047 0.004 0.006 0.039 0.041 0.012 0.0089 0.256 0.260 0.252 0.260 0.173 0.176 0.0256 BSC 8° 0.024 0.030 0087225C 11/12 ...
Page 12
... M74HC573 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice ...