max5886 Maxim Integrated Products, Inc., max5886 Datasheet - Page 15

• Manufacturer Part Number: max5886
• Description: Max5886 3.3v, 12-bit, 500msps High Dynamic Performance Dac With Differential Lvds Inputs
• Manufacturer: Maxim Integrated Products, Inc.

**Thermal efficiency is not the key factor, since the MAX5886 features low-power operation. The exposed pad is the key element to
Figure 11. GSM/EDGE Tx Mask Requirements
supply decoupling guidelines for high-speed, high-fre-
quency applications should be closely followed.
This reduces EMI and internal crosstalk that can signifi-
cantly affect the dynamic performance of the MAX5886.
Use of a multilayer printed circuit (PC) board with sepa-
rate ground and power-supply planes is recommend-
ed. High-speed signals should run on lines directly
above the ground plane. Since the MAX5886 has sepa-
rate analog and digital ground buses (AGND,
CLKGND, and DGND, respectively), the PC board
should also have separate analog and digital ground
sections with only one point connecting the two planes.
Digital signals should be run above the digital ground
plane and analog/clock signals above the analog/clock
ground plane. Digital signals should be kept as far
away from sensitive analog inputs, reference input
sense lines, common-mode input, and clock inputs as
practical. A symmetric design of clock input and ana-
log output lines is recommended to minimize 2nd-order
harmonic distortion components and optimize the
DAC’s dynamic performance. Digital signal paths
should be kept short and run lengths matched to avoid
propagation delay and data skew mismatches.
Performance DAC with Differential LVDS Inputs
ensure a solid ground connection between the DAC and the PC board’s analog ground layer.
-30
-60
-70
-73
-75
-80
-90
O
0.2 0.4 0.6
FREQUENCY OFFSET FROM CARRIER (MHz)
______________________________________________________________________________________
MEASUREMENT BANDWIDTH
1.2
30kHz 100kHz
1.8
3.3V, 12-Bit, 500Msps High Dynamic
6.0
IMD REQUIREMENT: < -70dBc
INBAND
OUTBAND
WORST-CASE
NOISE LEVEL
The MAX5886 supports three separate power-supply
inputs for analog (AV
(VCLK) circuitry. Each AV
should at least be decoupled with a separate 0.1µF
capacitor as close to the pin as possible and their
opposite ends with the shortest possible connection to
the corresponding ground plane (Figure 13). Try to
minimize the analog and digital load capacitances for
optimized operation. All three power-supply voltages
should also be decoupled at the point they enter the
PC board with tantalum or electrolytic capacitors.
Ferrite beads with additional decoupling capacitors
forming a pi network could also improve performance.
The analog and digital power-supply inputs AV
VCLK, and DV
age range of 3.3V ±5%.
The MAX5886 is packaged in a 68-pin QFN-EP
(package code: G6800-4), providing greater design
flexibility, increased thermal efficiency**, and optimized
AC performance of the DAC. The exposed pad (EP)
enables the user to implement grounding techniques,
which are necessary to ensure highest performance
operation. The EP must be soldered down to AGND.
Figure 12. 4-Tone MTPR Test Results
-100
-10
-20
-30
-40
-50
-60
-70
-80
-90
0
26
4-TONE MULTITONE POWER RATIO PLOT
(f
f
f
f
f
DD
T1
T2
T3
T4
A
BW = 12MHz
CLK
OUT
= 29.6997MHz
= 30.7251MHz
= 32.4829MHz
= 34.0209MHz
28
of the MAX5886 allow a supply volt-
= 300MHz, f
= -12dB FS
f
T1
DD
30
), digital (DV
f
OUT
DD
f
T2
CENTER
32
(MHz)
f
, DV
T3
34
= 31.604MHz)
DD
f
T4
, and VCLK input
36
DD
), and clock
38
DD
15
,