adv7181b Analog Devices, Inc., adv7181b Datasheet - Page 59
![no-image](/images/no-image-200.jpg)
adv7181b
Manufacturer Part Number
adv7181b
Description
Multiformat Sdtv Video Decoder
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADV7181B.pdf
(100 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adv7181b-SBTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBCPCZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBCPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bBSTZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adv7181bST
Manufacturer:
ADI/亚德诺
Quantity:
20 000
PIXEL PORT CONFIGURATION
The ADV7181B has a very flexible pixel port that can be config-
ured in a variety of formats to accommodate downstream ICs.
Table 78 and Table 79 summarize the various functions that the
ADV7181B pins can have in different modes of operation.
The ordering of components, for example, Cr vs. Cb or
CHA/B/C, can be changed. Refer to the SWPC Swap Pixel
Cr/Cb, Address 0x27[7] section. Table 78 shows the default
positions for the Cr/Cb components.
OF_SEL[3:0] Output Format Selection, Address 0x03[5:2]
The modes in which the ADV7181B pixel port can be configured
are under the control of OF_SEL[3:0]. See Table 79 for details.
The default LLC frequency output on the LLC1 pin is approxi-
mately 27 MHz. For modes that operate with a nominal data
rate of 13.5 MHz (0001, 0010), the clock frequency on the LLC1
pin stays at the higher rate of 27 MHz. For information on
outputting the nominal 13.5 MHz clock on the LLC1 pin,
see the LLC1 Output Selection, LLC_PAD_SEL[2:0],
Address 0x8F[6:4] section.
SWPC Swap Pixel Cr/Cb, Address 0x27[7]
This bit allows Cr and Cb samples to be swapped.
When SWPC is 0 (default), no swapping is allowed.
When SWPC is 1, the Cr and Cb values can be swapped.
Table 78. P15–P0 Output/Input Pin Mapping
Format and Mode
Video Out, 8-Bit, 4:2:2
Video Out, 16-Bit, 4:2:2
Table 79. Standard Definition Pixel Port Modes
OF_SEL[3:0]
0010
0011
0110-1111
Format
16-bit @ LLC2 4:2:2
8-bit @ LLC1 4:2:2 (default)
Reserved
15
14
13
YCrCb[7:0] OUT
Y[7:0] OUT
12
Rev. B | Page 59 of 100
11
LLC1 Output Selection, LLC_PAD_SEL[2:0],
Address 0x8F[6:4]
The following I
LLC1 (nominally at 27 MHz) and LLC2 (nominally at
13.5 MHz).
The LLC2 signal is useful for LLC2-compatible wide bus
(16-bit) output modes. See the OF_SEL[3:0] Output Format
Selection, Address 0x03[5:2] section for additional information.
The LLC2 signal and data on the data bus are synchronized. By
default, the rising edge of LLC1/LLC2 is aligned with the Y
data; the falling edge occurs when the data bus holds C data.
The polarity of the clock, and therefore the Y/C assignments to
the clock edges, can be altered by using the polarity LLC pin.
When LLC_PAD_SEL is 000, the output is nominally 27 MHz
LLC on the LLC1 pin (default).
When LLC_PAD_SEL is 101, the output is nominally 13.5 MHz
LLC on the LLC1 pin.
10
Data Port Pins P[15:0]
P[15:8]
Y[7:0]
YCrCb[7:0]
9
8
2
C write allows the user to select between the
7
6
Reserved
P[15: 0]
5
CrCb[7:0] OUT
Three-state
P[7: 0]
CrCb[7:0]
4
3
ADV7181B
2
1
0