tcm1a106m ROHM Co. Ltd., tcm1a106m Datasheet - Page 4
tcm1a106m
Manufacturer Part Number
tcm1a106m
Description
Chip Tantalum Capacitors Bottom Surface Electrode Type
Manufacturer
ROHM Co. Ltd.
Datasheet
1.TCM1A106M.pdf
(7 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
tcm1a106m8R-02
Manufacturer:
ROHM/罗姆
Quantity:
20 000
○
TC Series M Case
Temperature
Stability
Surge voltage
Loading at
High temperature
Terminal
strength
c
www.rohm.com
2009 ROHM Co., Ltd. All rights reserved.
Item
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Temp.
∆C / C
Df (tan δ)
L.C.
Appearance
L.C.
∆C / C
Df (tan δ)
Appearance
L.C.
∆C / C
Df (tan δ)
Capacitance
Appearance
TCM0G336
TCM0J226
TCM0J336
TCM0G336
TCM0J226
TCM0J336
TCM0G336
TCM0G336
TCM0J226
TCM0J336
−55 °C
Shall be satisfied the voltage on " Standard list "
+85 °C
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial value
+125 °C
Shall be satisfied the voltage on " Standard list "
Less than 1000% of initial value
There should be no significant abnormality.
Less than 200% of initial limit
Within ±20% of initial value
Less than 200% of initial limit
There should be no significant abnormality.
Less than 200% of initial limit
Less than 200% of initial limit
The measured value should be stable.
There should be no significant abnormality.
Others : Within +15/0% of initial value
Others : Within ±20% of initial value
Others : Within 0/−15% of initial value
Others : Within +20/0% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±15/−5% of initial value
: Within ±30% of initial value
: Within ±30% of initial value
: Within 0/−30% of initial value
: Within +15/-5% of initial value
: Within ±30% of initial value
: Within +20/-5% of initial value
Performance
−
4/6
Test conditions (based on JIS C 5101−1 and JIS C 5101− 3)
As per 4.29 JIS C 5101-1
As per 4.13 JIS C 5101-3
As per 4.26JIS C 5101-1
As per 4.14JIS C 5101-3
Apply the specified surge voltage every 5±0.5 min.
for 30±5 s. each time in the atmospheric condition of 85±2°C.
Repeat this procedure 1,000 times.
After the specimens, leave it at room temperature for
over 24h and then measure the sample.
As per 4.23 JIS C 5101-1
As per 4.15 JIS C 5101-3
After applying the rated voltage for 1000+36/0 h without
discontinuation via the serial resistance of 3Ω or less
at a temperature of 85±2°C, leave the sample at room
temperature / humidity for over 24h and measure the value.
As per 4.35 JIS C 5101-1
As per 4.9 JIS C 5101-3
A force is applied to the terminal until it bends to 1mm and
by a prescribed tool maintain the condition for 5s.
(See the figure below)
thickness=1.6mm
50
45
R230
20
45
F (Apply force)
(Unit : mm)
1
2009.11 - Rev.G
Data Sheet