at83c24nds-tisum ATMEL Corporation, at83c24nds-tisum Datasheet - Page 14
at83c24nds-tisum
Manufacturer Part Number
at83c24nds-tisum
Description
Smart Card Reader Interface With Power Management
Manufacturer
ATMEL Corporation
Datasheet
1.AT83C24NDS-TISUM.pdf
(42 pages)
- Current page: 14 of 42
- Download datasheet (809Kb)
Activation Sequence
Hardware Activation (DC/DC started with CMDVCC)
14
AT83C24
Initial conditions:
CARDDET bit must be configured in accordance to the smart card connector polarity.
IT_SEL bit, CRST_SEL bit (see CONFIG4 register) must be set and CARDRST bit (see INTER-
FACE register) must be cleared. A smart card must be detected to enable to start the DC/DC
(CVCC= 3V or 5V).
The hardware activation sequence is started by hardware with CMDVCC pin going high to low. It
follows this automatic sequence:
•
•
•
•
Note:
Note:
Figure 10. Activation sequence with CMDVCC
CIO / CC4 / CC8 and IO / C4 / C8 are respectively linked together (IODIS bit is cleared).
The DC/DC is started and CVCC is set according to the A0/3V pin: 5V (Class A) if A0/3V is
High and 3V (Class B) is A0/3V is Low.
CCLK signal is enabled (CKSTOP bit cleared) when CVCC has settled to the programmed
voltage (see Electrical Characteristics) and the level on A1/RST is 0. The CCLK source can
be DCCLK signal, CLK signal , A2/CK signals or CARDCK bit (see Figures 5).
CRST signal is linked with A1/RST pin as soon as A1/RST pin level is 0. A rising edge on
A1/RST pin set the CRST pin.
1. The card must be deactivated to change the voltage.
For NDS applications, the host usually starts activation with A1/RST = 0.
CMDVCC
A1/RST
CCLK
CVCC
CIO
CRST
4234F–SCR–10/05
Related parts for at83c24nds-tisum
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Smart Card Reader Interface with Power Management
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
IC 8051 MCU W/SMART CARD 28QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC 8051 MCU W/SMART CARD 28SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Smart Card Reader Interface with Power Management
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Smart Card Reader Interface with Power Management
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet: