v23809-j307-c13 Infineon Technologies Corporation, v23809-j307-c13 Datasheet - Page 4

• Manufacturer Part Number: v23809-j307-c13
• Description: Ac/dc Coupled Multimode 1.0625 Fibre Channel 1x9transceiver
• Manufacturer: Infineon Technologies Corporation

Regulatory Compliance
APPLICATION NOTE FOR 850 NM GBD FIBRE CHANNEL 1X9 TRANSCEIVER
Values of R1/2/3/4 may vary as long as proper 50
V
required for good EMI performance. Use short tracks from the
inductor L1/L2 to the module V
Siemens Microelectronics, Inc. • Optoelectronics Division • 19000 Homestead Road • Cupertino, CA 95014 USA
Siemens Semiconductor Group • Fiber Optics • Wernerwerkdamm 16 • Berlin D-13623, Germany
Siemens K.K. • Fiber Optics • Takanawa Park Tower • 20-14, Higashi-Gotanda, 3-Chome • Shinagawa-ku • Tokyo 141, Japan
www.smi.siemens.com/opto.html (USA) • www.siemens.de/Semiconductor/products/37/376.htm (Germany)
Feature
Electrostatic Discharge (ESD)
to the Electrical Pins
Immunity:
Electrostatic Discharge (ESD) to the Duplex
SC Receptacle
Immunity:
Radio Frequency
Electromagnetic Field
Emission:
Electromagnetic Interference (EMI)
EE
C1/2/3 = 4.7 F
or 100
C4/5 = 10 nF
R1/2 = 82 Ohm (depends on SerDes chip used)
R3/4 = 130 Ohm (depends on SerDes chip used)
L1/2 = 1 H
Siemens Transceiver
V23809-J307-C10/C13
SiemensTransceiver
V23809-J307-C10
Pre-
Amp
differential is provided. The power supply filtering is
VCSEL
Driver
Limiting
Amplifier
CC
Signal
Detect
RD–
RD+
RX/V
100R
CC
TX.
TXGND
RxGND
VCCRx
VCCTx
Standard
MIL-STD 883C
Method 3015.4
EN 61000-4-2
IEC 1000-4-2
EN 61000-4-3
IEC 1000-4-3
FCC Class B
EN 55022 Class B
CISPR 22
RxD
RxD
TxD
TxD
SD
termination to
9
8
7
6
5
4
3
2
1
C1
C2
Place R1/2/3/4/7/8 close to SerDes chip
Place R5/6 close to Siemens transceiver
R5/6 = 200 Ohm 270 Ohm
R7/8 = Biasing (depends on SerDes chip)
R9 = 500 Ohm
R9
The transceiver contains an automatic shutdown circuit. Reset is
only possible if the power is turned off, and then on again. (V
switched below V
SD to upper level
L1
L2
Comments
Class 1 (>1000 V)
Discharges of 15kV with an air discharge probe on the
receptacle cause no damage.
With a field strength of 10 V/m rms, noise frequency ranges
from 10 MHz to 1 GHz. No effect on transceiver performance
between the specification limits.
Noise frequency range: 30 MHz to 1 GHz
C4
C5
VCC
5 V
C3
VCC SerDes
5 V
TH
). Application Board available on request.
VCC
TX+
RD–
RD+
TX–
Serializer/
Deserializer
Gigabit
Transceiver
Chip
Receiver
PLL etc.
ECL/PECL
Driver
CC
TX