sx8723 Semtech Corporation, sx8723 Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/5/596/semtech_corporation_sml.jpg)
sx8723
Manufacturer Part Number
sx8723
Description
Sx8723 Zoomingadc? For Pressure And Temperature Sensing
Manufacturer
Semtech Corporation
Datasheet
1.SX8723.pdf
(53 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
sx8723CWLTDT
Manufacturer:
TI
Quantity:
128
Company:
Part Number:
sx8723E083TDT
Manufacturer:
Semtech
Quantity:
1 989
Company:
Part Number:
sx8723E083TDT
Manufacturer:
Maxim
Quantity:
100
ADVANCED COMMUNICATIONS & SENSING
Registers
The system has a bank of eight 8-bit registers: six registers are used to configure the acquisition chain
(RegAcCfg0 to 5), and two registers are used to store the output code of the analog-to-digital conversion
(RegAcOutMsb & Lsb).
With:
V1.5 © 2007 Semtech Corp.
RegACOutLsb
RegACOutMsb
RegACCfg0
Default values:
RegACCfg1
Default values:
RegACCfg2
Default values:
RegACCfg3
Default values:
RegACCfg4
Default values:
RegACCfg5
Default values:
Register Name
(r = read; w = write; rw = read & write)
OUT: (r) digital output code of the analog-to-digital converter. (MSB = OUT[15])
START: (w) setting this bit triggers a single conversion (after the current one is finished). This bit always reads back 0.
SET_NELC: (rw) sets the number of elementary conversions to 2 SET_NELC[1:0]. To compensate for offsets, the input signal is
chopped between elementary conversions (1,2,4,8).
SET_OSR: (rw) sets the over-sampling rate (OSR) of an elementary conversion to 2(3+SET_OSR[2:0]). OSR = 8, 16, 32, ..., 512,
1024.
CONT: (rw) setting this bit starts a conversion. A new conversion will automatically begin as long as the bit remains at 1.
TEST: bit only used for test purposes. In normal mode, this bit is forced to 0 and cannot be overwritten.
IB_AMP_ADC: (rw) sets the bias current in the ADC to 0.25*(1+ IB_AMP_ADC[1:0]) of the normal operation current (25, 50, 75 or
100% of nominal current). To be used for low-power, low-speed operation.
IB_AMP_PGA: (rw) sets the bias current in the PGAs to 0.25*(1+IB_AMP_PGA[1:0]) of the normal operation current (25, 50, 75 or
100% of nominal current). To be used for low-power, low-speed operation.
ENABLE: (rw) enables the ADC modulator (bit 0) and the different stages of the PGAs (PGAi by bit i=1,2,3). PGA stages that are
disabled are bypassed.
FIN: (rw) These bits set the over sampling frequency of the acquisition chain. Expressed as a fraction of the oscillator frequency,
the sampling frequency is given as: 11
PGA1_GAIN: (rw) sets the gain of the first stage: 0
PGA2_GAIN: (rw) sets the gain of the second stage: 00
PGA3_GAIN: (rw) sets the gain of the third stage to PGA3_GAIN[6:0] 1/12.
PGA2_OFFSET: (rw) sets the offset of the second stage between –1 and +1, with increments of 0.2. The MSB gives the sign
(0
PGA3_OFFSET: (rw) sets the offset of the third stage between –5.25 and +5.25, with increments of 1/12. The MSB gives the sign
(0
BUSY: (r) set to 1 if a conversion is running.
DEF: (w) sets all values to their defaults (PGA disabled, max speed, nominal modulator bias current, 2 elementary conversions,
over-sampling rate of 32) and starts a new conversion without waiting the end of the preceding one.
AMUX(4:0): (rw) AMUX(4) sets the mode (0
sets the sign (0
VMUX: (rw) sets the differential reference channel (0
positive, 1
positive, 1
Table 1 - Peripheral Registers to Configure the Acquisition Chain (AC)
straight, 1
negative); amplitude is coded with the bits PGA2_OFFSET[5:0].
negative); amplitude is coded with the bits PGA3_OFFSET[5:0].
and to Store the Analog-to-Digital Conversion (ADC) Result
PGA1_G
START
IB_AMP_ADC[1:0]
BUSY
7
0
0
0
0
-
FIN[1:0]
11
00
cross) AMUX(2:0) sets the channel.
DEF
SET_NELC[1:0]
6
0
ZoomingADC™ for Pressure and Temperature Sensing
500 kHz, 10
01
IB_AMP_PGA[1:0]
differential inputs, 1
PGA2_GAIN[1:0]
5
1, 1
11
00
V
17
250 kHz, 01
BATT
1, 01
10.
, 1
4
V
SET_OSR[2:0]
2, 10
Bit Position
REF
AMUX[4:0]
OUT[15:8]
OUT[7:0]
single ended inputs with A
PGA3_OFFSET[6:0]
00000
).
PGA3_GAIN[6:0]
125 kHz, 00
010
3
5, 11
0001100
0000000
10.
2
62.5 kHz.
PGA2_OFFSET[3:0]
ENABLE[3:0]
CONT
0
0000
0000
1
= common reference) AMUX(3)
0
www.semtech.com
VMUX
SX8723
0
0
0
-