mlx90111 ETC-unknow, mlx90111 Datasheet
mlx90111
Related parts for mlx90111
mlx90111 Summary of contents
Page 1
... MLX90111 128bit Read Write Transponder 128bit Read Write Transponder Package Sawed wafer on frame Bare die in blistertape SOIC-8 150mils Description The MLX90111 is a flexible 128 bit Read Write Transponder IC operating at 125kHz. designed for high performant and highly reliable RFID systems requiring multiple transponder memory. ...
Page 2
... Higher modulation levels will reduce the maximum Write distance. Note (6): Lot to lot spread on capacitance is 20%. Temperature shift is typically 0% on -40 C, and + MLX90111 128bit Read Write Transponder 128bit Read Write Transponder Test Conditions ...
Page 3
... Block diagram COIL Ctune POR CLOCK RECOVERY DEMODUL. SUPPLY VSS MLX90111 clamping (DC) [mA -20 -5 -10 -15 MLX90111 128bit Read Write Transponder 128bit Read Write Transponder SPEED Digital Controller CLOCK ADDR DATA DATA VDD - Page MLX90111 VDD VDD ...
Page 4
... Lock word: "01010101" Lock word: "01010101" MLX90111 128bit Read Write Transponder 128bit Read Write Transponder BITPOSITION (MSB first) WPW(FLAGS) BITPOSITION (MSB first) WPW(FLAGS) Page MLX90111 Rev 1.12 5-Feb-01 ...
Page 5
... Clock recovery The transponder takes its clock from the carrier frequency. Depending on the speed option, the carrier frequency is divided by 32(4kbaud), 64(2kbaud) to generate the bit rate. MLX90111 128bit Read Write Transponder 128bit Read Write Transponder Demodulator Read Write If the external RF field is AM modulated ...
Page 6
... This offer is only valid for large volume orders (>100k pieces). MLX90111 128bit Read Write Transponder 128bit Read Write Transponder Following table shows the configuration of the tune caps in relation to the tune bits: 1 ...
Page 7
... ID code in critical read mode, until removal from the RF field. Minimum field strength for reliable programming is set by the minimum induced e.m.f. Vacee on the transponder coil. MLX90111 128bit Read Write Transponder 128bit Read Write Transponder 2.3 Programming commands Two Command Fields are defined: CMF ...
Page 8
... Make sure to respect the nr of transponder clocks per bit, as specified below. All data sent by the reader have to be Return- To-One encoded. MLX90111 128bit Read Write Transponder 128bit Read Write Transponder 3.3 Transponder action The command is verified on its Parity and CRC values after the full command has been received ...
Page 9
... Transponder mode / operations Normal read Enter program mode: Stop modulation - Synchronize on Start bit - MLX90111 Timing Specifications in ms for a Carrier Freq = 125kHz, Tclk=8 s Speed Bit Period Freq/64 (2kbaud) Tclk*64 = 0.512 Freq/32 (4kbaud) Tclk*32 = 0.256 1. Modulation on Reader Antenna Tsetup FHIGH FLOW 2 ...
Page 10
... For a “0” bit, there is a transition the beginning of the bit period. In the middle of the bit period the state returns to 1. For a “1” bit, the level remains high for the entire bit period. MLX90111 128bit Read Write Transponder 128bit Read Write Transponder ...
Page 11
... Continuous Normal Read (Transmit ID) ASYNC detected Stop modulating Y Watchdog expired? Parity/WPW/CRC check N Write to ID? address[0..7] Write to address 8/9/A? N address MLX90111 128bit Read Write Transponder 128bit Read Write Transponder Critical Read=1? POR No Continuous Critical Read (Transmit ID OK Set Critical Read ...
Page 12
... However, Melexis assumes no responsibility for its use, nor for any infringements of patents or other rights of third parties which may result from its use. MLX90111 128bit Read Write Transponder 128bit Read Write Transponder SO8 Pinout Pin Name ...