adl5201 Analog Devices, Inc., adl5201 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
adl5201
Manufacturer Part Number
adl5201
Description
31.5 Db Range, 0.5 Db Step Size Programmable Vga
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADL5201.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
adl5201ACPZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
adl5201ACPZ-R7
Manufacturer:
ADI
Quantity:
58
Part Number:
adl5201ACPZ-R7
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADL5201
DIGITAL INTERFACE OVERVIEW
The ADL5201 DVGA has three digital control interface options:
The digital control interface selection is made via 2 digital pins,
MODE1 and MODE0, as shown in Table 5. There are two
common digital control pins, PM and PWUP. PM selects
between two power modes. PWUP is a power up pin. The gain
code used is 6 bit binary.
Physical pins are shared between 3 interfaces resulting in as
many as 3 different functions per digital pin (seeTable 4).
Table 5. Digital control interface selection truth table
MODE1
0
0
1
1
Parallel Digital Interface
The parallel digital interface uses 6 gain control bits and a latch
pin. The latch pin controls whether the input data latch is
transparent or latched. In transparent mode, gain changes as
input gain control bits change. In latched mode, gain is
determined by the latched gain setting and does not change
with changing input gain control bits.
Serial Peripheral Interface (SPI)
The SPI uses 3 pins (SDIO, SCLK and CS ). The SPI data register
consists of 2 bytes: 6 gain control bits, 2 attenuation step size
address bits, 1 read/write bit, and 7 do not care bits.
The SPI uses a bidirectional pin, SDIO, for writing to the SPI
register and for reading from the SPI register. In order to write
to the SPI register CS needs to be pulled low and 16 clock pulses
must be applied.
In order to read the SPI register value, the R/W bit needs to be
set high, CS needs to be pulled low, and the part clocked. Once
the register has been read out the R/W bit needs to be set low
and SPI put in write mode.
SPI fast attack mode is controlled by FA pin. A logic high on
the FA pin results in an attenuation selected by FA1 and FA0
bits in the SPI register.
•
•
•
Parallel Control Interface
Serial Peripheral Interface
Gain Step Up/Down Interface
MODE0
0
1
0
1
Interface
Parallel
Serial (SPI)
Up/Down
Up/Down
Rev. PrD | Page 8 of 10
Table 6. SPI 2-bit attenuation step size truth table
FA1
0
0
1
1
UP/DOWN Interface
The UP/DOWN interface uses two digital pins to control the
gain. Gain is increased by a clock pulse on UPDN_CLK (rising
and falling edges) when UPDN_DAT is high. Gain is decreased
by a clock pulse on UPDN_CLK when UPDN_DAT is low.
Reset is detected by a rising edge latching data having one
polarity with the falling edge latching the opposite polarity.
Reset results in minimum gain code 111111
UPDN_DAT
The step size is selectable by pins GS1 and GS0. The default step
size is 0.5dB. The gain code count will rail at the top and
bottom of the control range.
Table 7. Step size control truth table
GS1
0
0
1
1
UPDN_CLK
UP
Preliminary Technical Data
Figure 3. UP/DOWN Timing
Figure 4. 16 bit SPI Register
FA0
0
1
0
1
GS0
0
1
0
1
DN
Step Size (dB)
2
4
8
16
Step Size (dB)
0.5
1
2
4
bin
.
RESET