adl5811 Analog Devices, Inc., adl5811 Datasheet
adl5811
Available stocks
Related parts for adl5811
adl5811 Summary of contents
Page 1
... The ADL5811 is fabricated using a BiCMOS high performance IC process. The device will be available in a 5mm x 5mm 32- lead LFCSP package and operates over a −40°C to +85°C temperature range ...
Page 2
... ADL5811 ADL5811—Specifications Table 25 1900 MHz Parameter RF INPUT INTERFACE Return Loss Input Impedance RF Frequency Range OUTPUT INTERFACE Output Impedance IF Frequency Range 1 DC Bias Voltage LO INTERFACE LO Power Return Loss Input Impedance LO Frequency Range DYNAMIC PERFORMANCE Power Conversion Gain ...
Page 3
... CLK high duration ns minimum CLK low duration ns minimum CLK to LE setup time ns minimum LE pulse width DB2 DB1 DB22 (CONTROL BIT C3) (CONTROL BIT C2) Figure 2. Timing Diagram REV. PrA | Page ADL5811 DB0 (LSB) (CONTROL BIT C1 ...
Page 4
... ADL5811 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter Supply Voltage, V POS CLK, DATA Output Bias RF Input Power LO Input Power Internal Power Dissipation θ (Exposed Paddle Soldered Down) JA θ (At Exposed Paddle) JC Maximum Junction Temperature Operating Temperature Range Storage Temperature Range Stresses above those listed under Absolute Maximum Ratings Rating may cause permanent damage to the device ...
Page 5
... Supply Return for IF Amplifier. Must be grounded. IF Differential Open-Collector Outputs. Should be pulled-up to VCC using external inductors. IF Amplifier Bias Control. Supply Voltage for IF Amplifier. Exposed pad must be connected to ground. REV. PrA | Page LOIP 20 LOIN DATA 17 CLK ADL5811 ...
Page 6
... ADL5811 TYPICAL PERFORMANCE CHARACTERISTICS 25°C, as measured using typical circuit schematic with low-side LO unless otherwise noted 500 1000 1500 2000 RF FREQUENCY (MHz) Figure 4. Conversion Gain versus RF Frequency 500 1000 1500 2000 RF FREQUENCY (MHz) Figure 5 ...
Page 7
... Preliminary Technical Datasheet REGISTER STRUCTURE Figure 10 illustrates the register map of ADL5811. The ADL5811 uses only register 5. As such the Control Bits should be set all cases. The ENBL bit, DB7 respectively, when set to 0 will enable the part. By setting this bit to 1 the mixer will be powered down ...
Page 8
... Figure 11. ADL5811 Optimum Settings REV. PrA | Page Preliminary Technical Datasheet ...
Page 9
... Preliminary Technical Datasheet EVALUATION BOARD An evaluation board is available for the family of double balanced mixers, including the ADL5811. The standard evaluation board schematic is presented in Figure 12. The evaluation board is fabricated on a multilayer Rogers board. Table 4 details the various configuration options of the evaluation board. ...
Page 10
... BSC SQ PIN 1 INDICATOR TOP VIEW 1.00 12° MAX 0.85 0.80 0.35 SEATING 0.30 PLANE 0.25 ORDERING GUIDE Temperature Models Range ADL5811XCPZ-R7 1 −40°C to +85°C ADL5811-EVALZ Pb-free part. 0.60 MAX 24 7.75 BSC SQ 0.75 17 0.60 0.50 0.80 MAX 0.65 TYP 0.05 MAX 0.02 NOM COPLANARITY 0.80 0.08 BSC 0.20 REF COMPLIANT TO JEDEC STANDARDS MO-220-VLLB Figure 13. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ × ...