lt5506 Linear Technology Corporation, lt5506 Datasheet
![no-image](/images/manufacturer_photos/0/3/389/linear_technology_corporation_sml.jpg)
lt5506
Available stocks
Related parts for lt5506
lt5506 Summary of contents
Page 1
... C1 1nF OUT – I OUT IF DET C3 1.8pF + Q OUT – Q OUT LT5506 GND 5506 TA01 LT5506 40MHz to 500MHz with VGA U Total Harmonic Distortion vs IF Input Level at 1.8V Supply – 280MHz IF 280.1MHz IF, 2 – 570MHz 2xLO 800mV DIFFERENTIAL OUT P-P –40 –45 –50 –55 – ...
Page 2
... Single Ended, C 10pF LOAD P = –25.5dBm, 280MHz IF –25.5dBm, 280.1MHz (Note 7) IF ORDER PART TOP VIEW NUMBER LT5506EUF 12 STBY + 11 2xLO 17 – 10 2xLO PACKAGE 4mm) PLASTIC QFN = 125 C – ...
Page 3
... OUT Note 7: The gain control voltage V differential output voltage between and Q OUT OUT Note 8: The typical parameter is defined as the mean of the absolute values of the data distribution. LT5506 = –5dBm (Note 5 284MHz STBY = V , unless otherwise noted. (Note MIN TYP MAX 0 ...
Page 4
... LT5506 W U TYPICAL PERFOR A CE CHARACTERISTICS (Note 5 284MHz –30dBm, I and Q outputs 800mV IF IF unless otherwise noted. (Note 3) Supply Current vs Supply Voltage – 1.75 2.25 2.75 3.25 3.75 4.25 4.75 5.25 SUPPLY VOLTAGE (V) Gain and Noise Figure vs Control Voltage at 1.8V Supply ...
Page 5
... IF Input CW Power at 3V Supply 1 280MHz IF 1.2 1.0 0.8 – 0.6 0.4 0.2 –40 –30 –20 – INPUT CW POWER (dBm) 5506 G14 LT5506 = 570MHz –5dBm STBY = Total Harmonic Distortion vs IF Input Power at 1.8V Supply and 800mV Differential Out P-P – 280MHz IF 280.1MHz IF,2 – ...
Page 6
... LT5506 W U TYPICAL PERFOR A CE CHARACTERISTICS (Note 5 284MHz –30dBm, I and Q outputs 800mV IF IF unless otherwise noted. (Note 3) IF Detector Output Voltage vs IF Input CW Power and Supply Voltage 1 280MHz IF 1.2 5.25V 3V 1.0 1.8V 0.8 0.6 0.4 0.2 –40 –30 –20 – INPUT CW POWER (dBm) 5506 G16 CTIO S GND (Pins 1, 4, 17): Ground ...
Page 7
... differential AC input impedance of the LT5506 is about 200 , thus a 1:4 (impedance ratio) RF transformer with central tap can be used. In Figure 6, the evaluation board schematic is shown using a 1:4 transformer. The mea- sured input sensitivity of this board is about –82.6dBm for a 10dB signal-to-noise ratio. In the case matching circuit, the circuit of Figure 1 can be used ...
Page 8
... LT5506 U U APPLICATIO S I FOR ATIO C3 L1 56pF 56nH IF INPUT 5.6pF 120nH 56nH Figure 1. IF Input Matching Network at 280MHz Table 1. The Component Values of Matching Network L1, L2, L3, C1, C2 and C3. f (MHz) L1, L2(nH) C1, C2(pF 340 34 100 159 15.9 150 106 10.6 200 80 8.0 250 64 6.4 300 53 5 ...
Page 9
... However high level input temporarily overloads the linear ampli- fier, then the circuit will limit symmetrically, which will help to prevent the filter and output buffer from overload- ing. This speeds up recovery from an overload event, LT5506 2xLO – ...
Page 10
... F 0 – + – OUT OUT OUT OUT 1 12 GND STBY 2XLO – LT5506 – IF 2XLO 4 9 GND DET CC CTRL GND CC1 C15 C22 C16 1nF 1 F 1nF OVERLOAD R51 C25 ...
Page 11
... Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights Figure 8. Component Side Layout of Evaluation Board Figure 10. Bottom Side Layout of Evaluation Board LT5506 5506fa 11 ...
Page 12
... HARD VGA CLIPPER LPF I-MIXER 15nH 3 0 Q-MIXER 90 11 LPF HARD CLIPPER 3.3pF 39nH f/2 10 LT5506 3.3pF 0,1 Package 16-Lead Plastic QFN (4mm 4mm) (Reference LTC DWG # 05-08-1692) 4.00 0.10 (4 SIDES) 0.72 0.05 PIN 1 TOP MARK PACKAGE OUTLINE 0.30 0.05 0.65 BSC NOTE: 1. DRAWING CONFORMS TO JEDEC PACKAGE OUTLINE MO-220 VARIATION (WGGC) 2 ...