cgy196 ETC-unknow, cgy196 Datasheet

Page 1

GaAs MMIC Preliminary Data l Broadband Power Amplifier [ 800..3500 Mhz ] l DECT,PHS,PCS,GSM,AMPS,WLAN,WLL l Single Voltage Supply l Operating voltage range: 2.0to Pout = 25.5dBm at Vd=2.4V l Pout = 27.0dBm at Vd=3.0V l Pout = ...

Page 2

Functional Block Diagram RFin/Vg Pin # Configuration Name 1 RFin/Vg RF input power + Gate voltage [0V internal] 2 GND RF and DC ground 3 VD2 Pos. drain voltage of the 2nd stage 4 n.c. not connected 5 n.c. not ...

Page 3

Determination of Permissible Total Power Dissipation for Continuous and Pulse Operation The dissipated power is the power which remains in the chip and heats the device. It does not contain RF signals which are coupled out consistently. a) Continuous Wave ...

Page 4

Pulsed Operation For the calculation of the permissible pulse load P Use the values for P as derived from the above diagram and for the tot-DC from the following diagram to get a specific value. Pulse factor: P should ...

Page 5

Reliability Considerations This procedure yields the upper limit for the power dissipation for continuous wave (cw) and pulse applications which corresponds to the maximum allowed channel temperature. For best reliability keep the channel temperature low. The following formula allows ...

Page 6

Electrical characteristics [ 3.0V DECT-Application: PCB-Layout see page 25°C , f=1.89 GHz =50 Ohm, unless otherwise specified) Characteristics Supply current VD=3.0V; Pin = +0 dBm Supply current VD=3.0V; Pin = -10 dBm ...

Page 7

... Electrical characteristics [3.0V DECT-Application: PCB-Layout see page 9] 27,0 26,0 25,0 24,0 23,0 22,0 21,0 20,0 19,0 18,0 17,0 -11 - 30,0 29,0 28,0 27,0 26,0 25,0 24,0 23,0 22,0 21,0 20,0 -11 - Siemens Aktiengesellschaft Semiconductor Group CGY196 Vd=3.3V, duty cycle 10 Pin/dBm CGY196 VD=5.0V, duty cycle 10 Pin/dBm 7 7 CGY 196 60,0 55,0 50,0 45,0 40,0 35,0 30,0 25,0 20,0 Pout [dBm] PAE [%] 15,0 10 60,0 55,0 50,0 45,0 40,0 35,0 30,0 25,0 20,0 Pout [dBm] PAE [%] 15,0 10,0 ...

Page 8

... Siemens Aktiengesellschaft Semiconductor Group CGY196 2,0 3,0 4 CGY 196 + * I(mA) 0 Pout(dBm) -10 -20 -30 -40 5 GaAs 16.6.1998 1998-11-01 ...

Page 9

... Electrical characteristics [3.0V DECT-Application: PCB-Layout see page 9] -30,0 -35,0 -40,0 -45,0 -50,0 -55,0 -60,0 -65,0 -70,0 - -30,0 -35,0 -40,0 -45,0 -50,0 -55,0 -60,0 -65,0 -70,0 - Siemens Aktiengesellschaft Semiconductor Group Harmonic Distortion CGY196 Vd=3. Pin / dBm Harmonic Distortion CGY196 Vd=4. Pin / dBm GaAs CGY 196 16.6.1998 1998-11-01 ...

Page 10

Test Board Layout [3.0V DECT-Application f=1.89GHz ] Siemens Aktiengesellschaft Semiconductor Group 10 10 CGY 196 16.6.1998 1998-11- GaAs ...

Page 11

Electrical characteristics [2.4V DECT-Application: PCB-Layout see page 12 25°C , f=1.89 GHz =50 Ohm, unless otherwise specified) Characteristics Supply current VD=2.4V; Pin = +0 dBm Supply current VD=2.4V; Pin = -10 dBm Output ...

Page 12

... Pout, (Vd) | Pin=0dBm [pulsed mode: T=417 s, duty cycle 12.5%] 450 400 350 300 250 200 150 100 50 0 0,0 Siemens Aktiengesellschaft Semiconductor Group CGY196 2.4V Applikation I(mA) Pout(dBm) 1,0 2,0 3,0 4 CGY 196 -10 -20 -30 -40 -50 5,0 16.6.1998 1998-11- GaAs ...

Page 13

Test Board Layout [2.4V DECT-Application f=1.89GHz ] Siemens Aktiengesellschaft Semiconductor Group 13 13 CGY 196 16.6.1998 1998-11- GaAs ...

Page 14

... Type Package CGY196 GaAs MMIC Key-word Notes on Processing Preliminary soldering recommendation Foot Print Soldering soldering profile: ramp-up preheating ramp-up peak exposure to molten solder typ. solder temperature peak temperature ramp-down comments Solder paste thickness Control of soldering (voids) Jedec A-112A ...

Page 15

Published by Siemens AG, Bereich Halbleiter, Marketing-Kommunikation, Balanstraße 73, D-81541 München. copyright Siemens AG 1996. All Rights Reserved. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se, not for ...